Home > Error Code > Kenmore Elite He3 Error Code F11

Kenmore Elite He3 Error Code F11

Contents

Took my time with the soldering and less than 2 hrs after opening it up I was successfully testing the washer. Saved me a bundle of money, and it's really satisfying to NOT have to pay the mfr for this defective part!ReplyDeleteAnonymousJune 28, 2013 at 12:02 PMJust a quick note that I Call a qualified repair person if you are uncomfortable with any of these steps. I am so pleased with the service Ed provided - from answering all my questions, to the superb job he did on the CCU. Check This Out

Also the door will not open even if the pause/cancel button is pushed to end the cycle. Note: It takes special skill to solder and unless you're skilled in this area I do not recommend performing and soldering procedures. Try Circuit Board Medics in SC. You can only upload a photo (png, jpg, jpeg) or a video (3gp, 3gpp, mp4, mov, avi, mpg, mpeg, rm).

Kenmore F11 Error Code Oven

Unplug the washer before opening the cabinet. I have repaired many of these after others have attempted to do so, and it's amazing how much misinformation is out there on the web. "Here is his email and ebay He (the repairman) changed a motor on the pumb but still got the same code. I don't think it has any relays to replace.

The directions tell me to unsolder the wires at the relay (K1). I only resoldered the relay solders and tried an old electronics trick. Add a comment Add a comment Add Comment 1024 Step 3 Remove the top panel Edit Unplug the main power cord. Kenmore Elite Range F11 Error Replace the plastic case on the relay.

Thanks again ! Kenmore He3t Whirlpool Duet Board Repair For F11 Code But my error-code list says the F11 problem is with the Motor Control Unit (MCU), not the CCU. Each time it happened it was more challenging to reset it. Clearing the error and restarting the cycle may fix the problem temporarily, but is not a permanent fix.

Press Cancel then by pressing the drain spin button once on the left side then move to the spin speed button on the right. What Does F11 Mean On My Kenmore Washer Richard Sandell - 11/24/2013 Reply well its good but i think i am not facing problems regarding control board i think its main machine.... Just cleaned the board edge contacts and up and running. Could I get some help on this please.

Kenmore He3t Whirlpool Duet Board Repair For F11 Code

Yes No Voted Undo Score 11 Cancel Comments: + Great solution, it didn't occur to me that the vibration might break loose the solder joints. 04/24/2011 by mayer the actual relays If I close the door it will not re-open. Kenmore F11 Error Code Oven I noticed that my gentle cycle worked fine, so I thought I'd try. Kenmore Washer F1 Error Code You may find the link below informative together with all the links that blog gives you.

HMMMMMMM, back to the internet. his comment is here Has anyone else experienced this? Yes No Voted Undo Score 3 Cancel Comments: Yes, that is all that i had to do. Thanks everyone! 10/03/2015 by cyrilusa I took my board off as directed in all the excellent posts above. F11 Error Code Frigidaire Range

You could wreck your washer. AppliancePartsPros 23.054 weergaven 6:53 Washer Main Control Board Replacement –LG Washing Machine Repair (Part #EBR64144920) - Duur: 4:00. Only the outer two tabs have a locking notch holding the control unit to the crossbar. http://softacoustik.com/error-code/kenmore-elite-he3-error-code-f-11.php Proactively I removed the CCU board, carefully marking the location of each wire connector, taking photos, etc.

be the board? F11 Error Code Kenmore Elite He5t A tiny flat head screwdriver9. ft.

Help out by taking, editing, or uploading new ones!

I used a pencil eraser to clean off the copper strips that the connectors plug onto. I am so happy to find an under-$12 solution. I called Sears, they want money and 2 weeks! F11 Error Code Lg Range The testing can get pretty involved.

Press this button until "no-spin" lights. than any I've had before. Shame on the repairman. 05/12/2014 by mayer Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? navigate here Give the author +30 points!

From the research I've done I have discovered that my F11 errors are only happening when I do my washing in the Sanitary mode. ft. Your question was published, help is on its way! HMMMMMMM, back to the internet.

This MAY solve your problem. ft. After making progress at one end, switch to desoldering the contacts at the other end of the relay in the same fashion. I do NOT put vaseline on your board, nor do I add solder to the contacts.

Beoordelingen zijn beschikbaar wanneer de video is verhuurd. Top Load Washer - White See Details Kenmore 22352 4.2 cu. Searching by their SKU number (8212208) or the Omron mfr part number (G5LE-1-DC12) should help find it. I just checked all the wires and contacts and checked for cold solder joints and nothing.

Thanks for the blog.ReplyDeleteAnonymousFebruary 11, 2011 at 7:56 PMI also have fought with Fll and DL error codes for years... So I... Here's a link to that blog:http://www.flickr.com/photos/mysteryonionpatch/471156850ReplyDeleteButchFebruary 3, 2010 at 7:50 AMAfter doing some extensive reading and research I guess I should consider myself fortunate. January 22 by Lou I removed the circuit board.

My issue was I was getting the F11 code at the beginning.