Home > Error Code > Kenmore Elite He3 Washer Error Code F11

Kenmore Elite He3 Washer Error Code F11

Contents

Add a comment Add a comment Add Comment 1024 Almost done! Good luck. I pryed it open to find a circuit board inside. Good advice. 10/06/2014 by Raymond You will need a good magnifying glass and a bright light to see the ring cracks on the relay pins. Check This Out

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? For those who dont have a technician available to them, any local electronics repair house could do this for you. I had a load in the wash and the error code F11 came on and continued to flash and beep loudly. No code.

Kenmore F11 Error Code Oven

Am I looking for corrosion? My issue was I was getting the F11 code at the beginning. http://www.applianceaid.com/ Appliance Repair Aid Reply With Quote March 6th, 2007,06:26 PM #3 SGS1965 View Profile View Forum Posts Member Join Date Mar 2007 Location Austin Posts 3 F11 Error on my My wife and I have had a Kenmore Elite HE4t Washer since the early 2000's and got tired of paying a couple hundred bucks for periodic repair to address the relay

space age machine: F11 etc. - as one post says, excessive vibration is common over time. And I can not be held responsible for actions you take on your own. If this doesn't work, it's best you wait for the service tech. What Does F11 Mean On My Kenmore Washer Give the author +30 points!

Unsolder one relay at a time from the circuit board, clean or replace it, then solder it back in position. The part number is 285924 priced at $120.71. I just checked all the wires and contacts and checked for cold solder joints and nothing. Also do a forum search for the CCU and see if its taken care of other members with this problem.

Was this answer helpful? Kenmore Elite Range F11 Error Your question was published, help is on its way! I don’t know what a bad shock locks like, but assumed that after 15 years of use it wouldn’t hurt to replace all four, so I did. Was this answer helpful?

Kenmore He3t Whirlpool Duet Board Repair For F11 Code

Thanks again ! You could spatter molten solder or rosin in your eye and go blind. Kenmore F11 Error Code Oven The door locks, the water starts and then a few more seconds - F11. Kenmore Washer F1 Error Code http://www.tristaterepairs.com/washer-re...

You can only upload photos smaller than 5 MB. his comment is here by Manage My Life January 20th, 2012 Comment 0 votes Sorry, the above was from me. The final test was to apply 12v to close the contacts and bump the relay on the table. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. F11 Error Code Frigidaire Range

To unsolder a relay, start by heating the solder at one end of the relay, and gently pull the relay's plastic package with a finger on the hand holding the circuit This first step is optional, and explains how to release the door lock manually. Angry Ram 1.146.979 προβολές 13:51 How to Remove a Motor Control Unit (MCU) From Whirlpool Duet, Kenmore HE3, KitchenAid, & Maytag - Διάρκεια: 5:17. this contact form Do not attempt to duplicate these repairs yourself unless you understand how to safely perform electronic repairs in general.

Yes No Voted Undo Score 5 Cancel Comments: Amazing. Kenmore F1 Error Code Its a wonder it worked as well as it did. Results 1 to 10 of 10 Thread: Kenmore elite he3t f 11 error Thread Tools Show Printable Version Search Thread Advanced Search Display Linear Mode Switch to Hybrid Mode Switch

We suffered for 3 years of F11 errors.

Top Load Washer - White See Details Kenmore 41162 4.3 cu. Please give me some ideas on how to approach this problem. Yes No Voted Undo Score 2 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? F11 Error Code Kenmore Elite He5t Add a comment Add a comment Add Comment 1024 Step 3 Remove the top panel Edit Unplug the main power cord.

The ones from before when Whirlpool bought them, and there were a grand total of -2- belts, each of which was replaceable without tools by simply tilting the machine backwards. It is in the service manual, listing the codes as well as the error codes. 12/22/2012 by oldturkey03 Add a comment 0/1024 Cancel Post comment Are you sure you want to One comment My machine wont come in at all now an i just used it lakesha powell - 05/14/2015 Reply Add a comment Add Comment 1024 Step 4 Mark the wires navigate here Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc.

Yes No Voted Undo Score 11 Cancel Comments: + Great solution, it didn't occur to me that the vibration might break loose the solder joints. 04/24/2011 by mayer the actual relays Yes No Voted Undo Score 0 Cancel Comments: robert, get the service manual from here, it should help you with your washer. Thanks for the info. Motor Control Unit MCU Repair$129.99 This is a repair service for your existing Whirlpool, Kenmore, or Maytag motor control unit (MCU) with a 1 business day turnaround.

There are three blue wires that go to the MCU from the CCU. The F01 error usually is intermittent at first but does become more consistent as time goes... Problem looks like design error. Help out by taking, editing, or uploading new ones!