Home > Error Code > Kenmore He3t F11 Error Code

Kenmore He3t F11 Error Code


Add a comment Add a comment Add Comment 1024 Step 2 Safety first! Some suggest that the door lock solenoids may be the cause of the electrical failure. I read most of the F11 postings I could find (one site had hundreds of posts on it). I can do some tests with an ohmmeter. this contact form

I couldn't get the top part to release from the steel bracket at the top. To remove the lid, remove the three screws along the back that hold it in place using either a T20 Torx screwdriver or a 9/32" socket driver. After reading the Fault codes provided by the manufacturer I am left scratching my head. You'll want to get an ohms reading of 60 for the solenoids.

Kenmore F11 Error Code Oven

I had performed every other repair listed, with no success. Add your answer Sign in to answer a question 1 Answer from this member: What does the F11 error code mean on my Kenmore Elite Quiet Pak2? General Information : The F11 I’ve just finished my 4th load without a problem. I have the HE2plus.

at 1:15 PM 25 comments Labels: Whirlpool Duet F11 Error Home Subscribe to: Posts (Atom) Blog Archive ▼ 2009 (2) ▼ January (2) How to Fix Your Kenmore HE4t F11 Code Before I put my board back together again I used a magnifying glass to try to spy any solders that bled onto the connector adjacent. Replace the plastic case on the relay. What Does F11 Mean On My Kenmore Washer And, when the washer is not in use, leave the front door slightly ajar to air out.

The final test was to apply 12v to close the contacts and bump the relay on the table. Unplug the washing machine! Your question was published, help is on its way! I just checked all the wires and contacts and checked for cold solder joints and nothing.

Prior to that it would stop working about every other load. Kenmore Elite Range F11 Error Add a comment Add a comment Add Comment 1024 Step 6 Circuit board repair and replacement Edit There are three or five relays on the circuit board. Circuit Board Medics 41.360 προβολές 9:57 Whirlpool Fault Codes - Διάρκεια: 3:39. Wow. $1.26 each.

Kenmore He3t Whirlpool Duet Board Repair For F11 Code

misc - May 20 Reply Thanks for the precise instructions. Just a thought. Kenmore F11 Error Code Oven Not being able to tell for sure I re-soldered it anyway. Kenmore Washer F1 Error Code Was this answer helpful?

Jake Appliance Repair School 1987-1988 Star Appliance Tech. 2 yrs. 1988-1990 Wards Appliance Tech. 11 yrs. 1990-2001 Sears Appliance Tech. 4 yrs. 2001-Oct. 2005 Jake's Appliance Repair Nov. 2005-present Look-Up & http://softacoustik.com/error-code/kenmore-elite-washer-he3t-error-code-f11.php It has done a few loads so far and it seems to be the correct solution to the problem. It will release the door lock. I bought this in 2004 and no problems until this F11 error that started this past week. F11 Error Code Frigidaire Range

Reply With Quote September 16th, 2007,01:20 AM #9 Ezed View Profile View Forum Posts Premium Member Join Date Sep 2007 Location 90803 Posts 17 I am trying to fix a HE2plus You could spatter molten solder or rosin in your eye and go blind. At first it would occur at either the final 11 minute or 2 minute stage, and only randomly — not every load. navigate here I have even seen one post where the poster stated that he had renewed the relays but had altered the cicuitry so that the relay that is subjected to the full,

A tiny flat head screwdriver9. Kenmore F1 Error Code If you must buy parts, here they are: http://www.repairclinic.com/Shop-For-Par... The five relays were less than $20 with shipping, so if the fix lasts awhile I intend to order several replacements while I can still get them.

The machine has been working wonderfully for a week.

I had never heard of these "Ring Cracks"... Yes No Voted Undo Score 0 Cancel Comments: I replaced the two relays on the CCU. Please use this interactive troubleshooting guide to determine which component is causing your error code(s). F11 Error Code Kenmore Elite He5t Anyway, when I finally got 'ready' to do this repair I took the stacked-on-top dryer off of it and in a last ditch effort, decided to plug it in....

He said not to bother since it was probably the Computer. I chose not to bother with the boards' recommendations to take apart and clean the solenoids and relays - I also didn't resolder them[UPDATE: December 12th, 2009. I usually suggest a technician do this but if you're comfortable and confident in your do-it-yourself abilities the instructions to remove the top (image #2) and bottom (image #3) access panels his comment is here Reach up inside the right hand side behind the door latch, and you should be able to feel a 1" diameter ring.

Yes No Voted Undo Score 3 Cancel Comments: Yes, that is all that i had to do.