Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). Check the MCU by looking for operations of the drive motor. 7. If no damage to wires and all connectors okay, proceed to step C. It will try to unlock the door six times before displaying the error code. navigate here
It starts beeping and the error code appears. F22 - Key Sensitivity Problem - Disconnect power for one minute and check to see if error reappears once power has been restore. If the wiring is okay, replace the oven door lock assembly. Contact Us DoItYourself.com Mobile Site Privacy Statement Top All times are GMT -7.
Plug in washer or reconnect power. 5. Plug in washer or reconnect power. 5. FdU - Door Unlock Error - It is possible the door lock mechanism is broken or the door switch/lock unit has failed.
Possible Causes / Procedure 1. If it overheats only when in use, disconnect electrical power from the oven and allow the oven to cool to room temperature. Electronic Range Control, ERC, Electronic Oven Control, EOC, control board, and clock all refer to the same part. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Check for plugged or kinked inlet hoses, as well as plugged screens in the inlet valves.
If error still remains after power has been restored, replace touch control module. (control board) F12 - Electronic Board and Touch Module Communication Error - Disconnect power for one minute and Kitchenaid Refrigerator Error Codes stoppedsnoring 25.554 weergaven 11:02 Why is My Oven Beeping and Saying F2? - Duur: 2:43. F1-E6 - Latch Signal Mismatch Error - Disconnect power for at least 30 seconds and then reconnect.
Questions of a Do It Yourself nature should be submitted to our "DoItYourself.com Community Forums". Kitchenaid Dishwasher Error Codes Note: Applies to all F5-E... I would just check all your wiring carefully to look for anything that may be shorted. All rights reserved.
SUD - Suds Lock (Too Much Detergent Detected - Make sure drain hose is not plugged or kinked and disconnect power and unplug unit. click resources Check the MCU by looking for operations of the drive motor. 6. Kitchenaid Error Code F2e1 F1-E3 - Wiring Harness Cavity Size Does Not Match Stored Value - Check the jumpers in the harness to make sure they agree with the actual oven size. Kitchenaid Oven Error Code F6e0 Replace failed component.
Unplug washer or disconnect power. 3. check over here Check CCU is also operational by performing a diagnostic test or any cycle. F13 - Internal CPU checksum Error(s) - Disconnect power for one minute and check to see if error reappears once power has been restore. Check for crack or holes in the washer tub and pressure switch hose. 2. Kitchenaid Oven Error Code F2e0
KitchenAid Pro Line Front Loading Gas and Electric Dryer Fault Codes (Models KHEV01RSS and KHGV01RSS) PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. A double oven will have two of each switch and one common wire. 1. It's fast and easy to create one. http://softacoustik.com/error-code/kitchen-aid-error-code.php If failure remains, replace the touch control module.
Check wire harness connections between the drive motor and the Motor Control Unit (MCU), and between the MCU and the Central Control Unit (CCU). 3. Kitchenaid Oven Error Code F9e0 Fault Codes Fault Codes Admiral Bosch Dacor Estate Frigidaire GE Gibson Hotpoint Jenn Air Kelvinator Kitchen Aid Magic Chef Maytag Roper Sears / Kenmore Tappan Thermador Whirlpool We are Safe, Secure, Log in om je mening te geven.
Remember: The oven control board (clock) measures resistance of sensor circuit, not actual oven temperature. Check the door switch/lock for any debris or foreign objects. We welcome your comments and suggestions. weblink F15 Motor control unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode.
If the meat probe connection jack and wiring harness are okay, replace the meat probe. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 3. If error continues, replace touch control module. If connections are ok, then check individual switches as outlined for the F5 error code.
Sometimes it takes a lot of opening and closing to get rid of the errors.