Reconnect any loose wires on the oven temperature sensor. Close Chat is currently unavailable We're sorry! Possible Causes / Procedure 1. User interface, Wire harness F2/E1 Defective button on the user interface Disconnect electrical power from the oven and replace the user interface. his comment is here
F15 Motor control unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. F10 - Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot) - Check for proper installation and ventilation, and make sure unit is not located near a heat source. Check sensor, sensor harness and sensor harness connection at sensor and oven control. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock). This Site
Check the electrical connections at the pump and make sure the pump is running. 4. If a failure occurs during high-speed spin, the door will be unlocked after three minutes. Replace the door lock assembly if visibly damaged. F1-E2 - UL A/D Error(s) - Disconnect power for at least 30 seconds and then reconnect.
Replace failed component. Check for drain pump failure. 6. The door should now be unlocked. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Press and HOLD start to continue the cycle, or press off/pause to clear display.
F2 - E3 Keypad held down too long, or keypad is shorted. Kitchenaid Refrigerator Error Codes Replace failed component. F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser.
FdU - Door Unlock Error - It is possible the door lock mechanism is broken or the door switch/lock unit has failed.
If the wiring is okay, replace the oven door lock assembly. Kitchenaid Dishwasher Error Codes If the wire harness connections are okay, replace the user interface. Measure door switch (door open = switch open small low voltage terminals). Verify there is not a siphon problem. 2.
Loading... http://www.searspartsdirect.com/wall-oven-repair/error-codes/kitchenaid-wall-oven-error-codes.html If the error code appears while the door is closed and locked, press "Stop" or "Clear," and press on the top-right portion of the oven door to release the latch. Kitchenaid Oven Error Code F2e1 Don't know your product's model number and need help locating it? Kitchenaid Oven Error Code F6e0 F1 Board failure Replace control board (also called ERC or clock).
Check the MCU by looking for operations of the drive motor. 6. http://softacoustik.com/error-code/kitchenaid-electric-range-error-code-f2-e1.php Learn More for questions or assistance, call 1-800-252-1698 (Se Habla Español) M-F6:30 a.m. - 10:00 p.m. OR If the control has turned the water valves on, and after 8 minutes, the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the F7 - Function Key Stuck - Replace control board (clock). Kitchenaid Oven Error Code F2e0
Honolulu, HI About Us DIY Blog Our Story Core Values Locations Rave Reviews Affiliates Program Job Listings My Account Sign In My Account Order History Shopping Cart Our Policies Terms of Check/clean drain pump filter of foreign objects. 5. F1-E1 - EEPROM Checksum Error - Disconnect power for at least 30 seconds and then reconnect. http://softacoustik.com/error-code/kitchenaid-range-error-code-f2-e1.php FdL - Door Lock Error - It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed.
If failure remains, replace board connection cable between touch control module and electronic control. 4. Kitchenaid Oven Error Code F9e0 Repeat steps A and B for door switch. 3. Q: How does a glass stove top heat?
Find Parts ^ top Kitchen Aid Cooktop Fault Codes Electronic Touch Ceramic 30 inch. Close Member Exclusive Not a member? Make sure the drain pump is free from debris or foreign objects and then reconnect power and plug unit in. Kitchenaid Error Code F8e0 Look for pinched wire.
Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab. Check wire harness connections to the MCU, the motor, and Central Control Unit (CCU). 3. User interface F3/E0 Upper oven temperature sensor is defective Disconnect electrical power from the oven. check over here In this case, replace control board (also called ERC or clock).
Reconnect any loose wires on the oven door lock assembly wire harness. If ok, replace probe. Check MCU by looking for operations of the drive motor and check drive motor for powered rotations. To return a part, you must first obtain a Return Authorization number by calling 888-205-0966 or visiting our website at www.SearsPartsDirect.com and chat with a Parts Trusted Advisor.
Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... Unplug washer or disconnect power. 3.