Home > Error Code > Kitchenaid Stove Error Codes

Kitchenaid Stove Error Codes

Contents

If code re-appears, replace control board (also called ERC or clock). Possible Causes / Procedure 1. Check/clean drain pump filter of foreign objects. 5. Replace the door lock assembly if visibly damaged. http://softacoustik.com/error-code/kitchenaid-stove-error-code.php

If ok, replace probe. E4 Tumbler rotation failure If during a cycle the tumbler rotational speed drops to 0, all outputs will be turned off and error code E4 will be displayed. Check dispenser motor for powered rotations. Unplug washer or disconnect power. 3.

Kitchenaid Error Code F2e1

More Fun Back To Fault Codes Admiral Fault Codes Whirlpool Appliance Fault Codes Roper Fault Codes Gibson Appliance Fault Codes Hotpoint Appliance Fault Codes Kelvinator Appliance Fault Codes KitchenAid Appliance Fault Verify CCU operation by running a Diagnostic test or any cycle. If failure remains, replace board connection cable between touch control module and electronic control. 4. Disconnect power and unplug unit to check wire harness connections to the Central Control Unit (CCU) and the door switch/lock unit.

Cooktop KECC568MBL Failure Indication Failure Code Fault Code Description Solution F03 One or more keys permanently pressed 1. F2-E1 - Touch Pad Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. F8 Board failure Replace control board (also called ERC or clock). Kitchenaid Oven Error Code F2e1 Stuck Shorted Key Check wires and connectors from control to latch switch, then from latch switch to control.

F6 indicates a missing AC signal, which is caused by improper voltage in the... If the wire harness is already plugged in, it’s likely that either the harness or keypad has failed; replace the keypad, which includes the harness. Press PAUSE/CANCEL two times to clear the display. http://www.appliancepartspros.com/repair-help/kitchenaid-fault-codes.html Close Member Exclusive Not a member?

Replace is defective. Kitchenaid Dishwasher Error Codes Reconnect any loose wires on the meat probe connection jack. Electronic oven control board F2/E0 User interface won’t respond Disconnect electrical power from the oven. F06 Drive motor tachometer error The control is unable to properly detect motor speed and the machine will shut down.

Kitchenaid Refrigerator Error Codes

Check drive belt. 4. http://www.appliancetimers.com/failure-code-page?manufacturer=ka&type=r Clean the glass surface and remove all objects placed on it. 2. Kitchenaid Error Code F2e1 Log in om ongepaste content te melden. Kitchenaid Oven Error Code F6e0 Possible Causes / Procedure 1.

Check wire harness connections to the dispenser motor and Central Control Unit (CCU). 4. this content Inloggen Laden... Gepubliceerd op 25 jan. 2016I need your help regarding KitchenAid oven error codes.Part of the answer depends on whether your oven has two digit or four digit error codes.I thought a Replace the pump. ^ top F05 Water temperature sensor error If during the water heating step in the wash cycle, the water temperature sensor (NTC) value is out of range, the Kitchenaid Oven Error Code F2e0

F03/F12/F13/F22 The F03, F12, F13 and F22 codes refer to problems within the ERC. Open the control panel and reconnect any loose wiring connections. F05 - Water Temperature Sensor Error - Unplug and disconnect power to the unit and check connections to the water temperature sensor. http://softacoustik.com/error-code/kitchenaid-stove-error-code-f6e0.php F36 - Temperature Probe Hardware Error - Disconnect power for one minute and check to see if error reappears once power has been restore.

Disconnect power and unplug unit to check door switch/lock unit. Kitchenaid Oven Error Code F9e0 RepairClinic.com 13.299 weergaven 4:59 How to Fix an F1 Error On a Kenmore or GE Range - Duur: 11:41. Check CCU is also operational by performing a diagnostic test or any cycle.

OR If the control has turned the water valves on, and after 8 minutes, the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the

Proceed by checking the drain hoses for proper connection and kinks. F15 Motor control unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode. Replace failed component. Kitchenaid Oven Error Code Pf For SELF CLEAN models: check door lock operation. 3.

FdL - Door Lock Error - It is possible the door lock mechanism is broken or removed, or the door switch/lock unit has failed. F13 - Dispenser Circuit Error - Disconnect power and unplug unit to check mechanical linkage from dispenser motor to top of dispenser. Press PAUSE/CANCEL twice to clear the display. http://softacoustik.com/error-code/kitchenaid-stove-error-code-f2e1.php Reach up along the inside of the front panel and locate the bottom of the door latch assembly, where there should be a tear-drop shaped tab.

F14 EEPROM error The Central Control Unit (CCU) receives its data from an EEPROM onboard the CCU. F36 - Temperature Probe Hardware Error - Disconnect power for one minute and check to see if error reappears once power has been restore. Check the wire harness connections to the door switch/lock unit and Central Control Unit (CCU).