Home > Error Code > Kitchenaid Superba Error Codes

Kitchenaid Superba Error Codes

Contents

Check the electrical connections at the pump and make sure it is operational with no debris or blockage. Disconnect power for 1 minute. 2. Click here for more information on other Kitchen Aid Parts from PartSelect.com Back to top Tweet PartSelect.com Home Contact About Us Help Privacy Policy Terms of Use Just For Fun! Find Parts ^ top Kitchen Aid Front Loading Automatic Washer Fault Codes (Model KHWS01PMT/ WH) Failure Code Fault Code Description Solution FH No water detected entering machine or pressure switch trip navigate here

Unplug washer or disconnect power for two minutes. 2. OR If the control has turned the water valves on, and after 8 minutes, the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the F4 - Shorted Oven Temperature Sensor (RTD) - Replace oven temperature sensor (RTD). Possible Causes / Procedure 1.

Kitchenaid Error Code F2e1

Close

FREE Standard Shipping on orders of $90 or more Purchase requirement calculated before taxes and shipping charges and after other discounts have been applied and must be made Check wire harness connections to pressure switch, drain pump, and Central Control Unit (CCU). It has been a few weeks since this last happened so I'm going from memory.

Check drive belt. 4. If failure remains, replace the touch control module. If a failure occurs during high-speed spin, the door will be unlocked after three minutes. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key F15 Motor control unit (MCU) error If the MCU detects multiple resets or errors during a wash cycle it will go into this error mode.

Select the 'cancel' function and wait 60 seconds. Kitchenaid Refrigerator Error Codes Check wire harness connections to the drain pump, pressure switch, and Central Control Unit (CCU). 4. Possible Causes / Procedure 1.

Unplug washer or disconnect power. 3.

Unplug the unit and disconnect the power to check all wire harness connections to the inlet valve, pressure switch, drain pump, flow meter, and Central Control Unit (CCU). Kitchenaid Dishwasher Error Codes Offer valid for online purchases only. Verify CCU operation by running a Diagnostic test or any cycle. Check the jumpers in the harness to make sure they agree with the actual oven size.

Kitchenaid Refrigerator Error Codes

Remember Me? view publisher site There is no connection between the oven door and the control panel. Kitchenaid Error Code F2e1 It will try to unlock the door six times before displaying the error code. Kitchenaid Oven Error Code F6e0 Check for proper installation, verify the unit is not located near a source of heat and has proper ventilation. 2.

Close Thank you! check over here F2:E3 followed by F2:E0. E6 Exhaust high limit fault If the exhaust temperature goes above 87.7°C (190°F) all outputs will turn off and E6 will be displayed. Replace is defective. Kitchenaid Oven Error Code F2e0

Reply With Quote December 15th, 2013,09:58 PM #3 mclintock View Profile View Forum Posts Premium Member Join Date Aug 2010 Location East Coast Posts 22 Hi Jeff, I will write them Check the drive belt and reconnect power and plug unit in. Once the F2 code appears, select 'cancel' and observe for one minute for errors. his comment is here Note: A power glitch may cause this error.

F9 Oven door lock failure Check wiring to door lock switch (the wire harness may be connected wrong). Kitchenaid Oven Error Code F9e0 Replace failed component. If too much detergent was used, run the unit through a Rinse/Spin cycle, and then run a Normal cycle without adding detergent.

If failure remains, replace the electronic control. 5.

If connections are not damaged, reconnect power and hold down any key until the F5 error clears. Check the door switch/lock for any debris or foreign objects. Share the good news, like us, and tweet. Kitchenaid Error Code F8e0 Unplug washer or disconnect power. 3.

Reconnect power. 3. Remove the lower toe panel. 3. Clearing your browser history may delete your saved models. weblink Press CANCEL.