Home > Error Code > Kitchenaid Supra Error Codes

Kitchenaid Supra Error Codes

Contents

Your cache administrator is webmaster. If the elements are okay, replace the electronic oven control board. F06 - Drive Motor Tachometer Error (Unable to Detect Motor Speed) - Check the shipping system including shipping bolts, spacers, and cables are removed and unplug unit and disconnect power. Check resistance of heating element if present in model, for abnormal reading (infinity). his comment is here

KitchenAid Front Loading Gas and Electric Dryer Fault Codes (Models KGHS01PMT/WH and KEHS01PMT/WH) PF - Power Failure - PF error code indicates a power failure during the dryer's cycle. F10 - Motor Control Unit (MCU) Heat Kink Thermal Trip (Too Hot) - Check for proper installation and ventilation, and make sure unit is not located near a heat source. Replace failed component. If error continues, replace electronic control (control board) and if error still persists, replace the touch module (touch pad). http://www.partselect.com/JustForFun/Kitchen-Aid-Appliance-Fault-Codes.aspx

Kitchenaid Error Code F2e1

Continue Reading Keep Learning How many KitchenAid refrigerator models are there? It sounds like a loose or a bad connection in the control section. Return to Search Results Major Appliances Black Stainless Cooktops Wall Ovens Refrigerators Undercounter Refrigerators Ranges Microwaves Dishwashers Disposers & Compactors Warming Drawers Hoods & Vents Grills Water Filters Shop Kitchenaid Countertop

Select 'cancel' and observe for one minute for errors. Reconnect any loose wires on the oven door lock assembly. To manually unlock the unit, unplug the power cord from the outlet and remove the toe panel. Kitchenaid Oven Error Code F2e1 Stuck Shorted Key F1-E6 - Latch Signal Mismatch Error - Disconnect power for at least 30 seconds and then reconnect.

Help Remember Me? Kitchenaid Refrigerator Error Codes ApplianceHelpOnline 336.100 προβολές 3:58 KitchenAid Probe Fix KitchenAid Model KEBS207SSS00 - Διάρκεια: 1:57. You can try checking the door switch, check the latch for interference –A broken door hinge or loose door seal in the way would be obvious.And if that isn’t it, power Check wire harness connections to the motor, Motor Control Unit (MCU), and Central Control Unit (CCU).

Test the door lock and the relay operation, and correct as necessary. Kitchenaid Oven Error Code F9e0 Proceed by checking the drain hoses for proper connection and kinks. Q: How many amps does a refrigerator pull? Turn off hot and cold water to faucets and unplug the unit before proceeding.

Kitchenaid Refrigerator Error Codes

F2-E1 - Touch Pad Cable Unplugged - Check the connection between the touch pad (keypad) and control board (clock) to make sure it is secure. https://www.reference.com/home-garden/check-error-codes-kitchenaid-refrigerator-a712b2dd7f05c41b KitchenAid Cooktop Fault Codes (Model KECC508MBL) F03 - One or More Eyes Permanently Pressed - Clean glass surface and remove all objects placed on it. Kitchenaid Error Code F2e1 May not be used with any other coupon, associate discount, or during Family & Friends or Member events. Kitchenaid Oven Error Code F2e0 Replace failed component.

Unable to proceed the request.Please try again © 2016 Sears Brands, LLC Privacy policy California privacy policy Careers Product recalls Terms of use Hide for questions or assistance, call1-888-206-3625 (Se Habla this content F15 - Motor Control Unit (MCU) Error -Disconnect power and unplug unit to check wire harness connections to the motor, MCU, and Central Control Unit (CCU). More Fun Back To Fault Codes Admiral Fault Codes Whirlpool Appliance Fault Codes Roper Fault Codes Gibson Appliance Fault Codes Hotpoint Appliance Fault Codes Kelvinator Appliance Fault Codes KitchenAid Appliance Fault If the elements are okay, replace the electronic oven control board. Kitchenaid Oven Error Code F6e0

Note: Unit will attempt to unlock itself during this error six times before displaying this error code. out of box M Get Weekly DIY Guides & Inspiration Life Made Easier. Victor Husary 10.857 προβολές 1:57 Kitchenaid & Whirlpool Wall Oven Diagnostic - Does Not Bake or Broil - KEBC247VSS02 - Διάρκεια: 6:19. weblink Opening and closing the door 5 times (no fewer) so the light goes out each time must do some sort of code reset.

Gently pull the tab down approximately 1/4 inch or until a 'click' is heard. Kitchenaid Dishwasher Error Codes It does this multiple times a year and seems to do it in spurts but then it will be fine for a few weeks. Disconnect power and unplug unit to check wire harness connections to the CCU and the touch pad/LED assembly.

Clean the ribbon connectors and any spills that might have gotten under there with warm water on a damp rag.

F8 - Control Board Failure - Replace control board (clock). Press 1. 6. Quick Question! Kitchenaid Error Code F8e0 Verify Central Control Unit (CCU) is operating properly by running a diagnostic test or any cycle.

F1 - Control Board Failure - Replace control board (clock). If the meat probe connection jack and wiring harness are okay, replace the meat probe. F1-E2 - UL A/D Error(s) - Disconnect power for at least 30 seconds and then reconnect. http://softacoustik.com/error-code/kitchenaid-stove-error-codes.php F21 / F22 - Central Control Unit (CCU) / Touch Pad / LED Assembly Error - Check that the touch pad/LED assembly is working by selecting different cycles and changing the

About eHow Advertise Write For eHow Contact Us Connect with us Terms of Use Report Copyright Ad Choices en-US Privacy Policy Mobile Privacy demandmedia.com © 1999-2016 Demand Media, Inc. Recall Alerts Careers PartSelect Canada Free Repair Help Appliance Repair Instant Repairman Dishwasher Dryer Microwave Range / Stove / Oven Refrigerator Washing Machine Helpful Resources PartSelect Community Twitter Facebook Page YouTube F6/F7/F8/F9 Error codes F6 through F9 indicate circuit problems. F36 - Temperature Probe Hardware Error - Disconnect power for one minute and check to see if error reappears once power has been restore.

If error continues, replace touch control module. Usually the error code goes away but often it is immediately followed up with F0 E0 (replace control). Because these technicians are factory-authorized by KitchenAid, they are a solid authority to understand particular error codes. Reconnect power and plug unit in.

Press and hold any key to clear the error code and F2 code should appear. Incapsula incident ID: 275001300112538439-248717523155093541 Υπενθύμιση αργότερα Έλεγχος Υπενθύμιση απορρήτου από το YouTube, εταιρεία της Google Παράβλεψη περιήγησης GRΜεταφόρτωσηΣύνδεσηΑναζήτηση Φόρτωση... Επιλέξτε τη γλώσσα σας. Κλείσιμο Μάθετε περισσότερα View this message in Yes No Thanks!