Home > Error Code > Laserjet 4si Error Codes

Laserjet 4si Error Codes

Contents

On the II and III Series printers, this error message can be caused by a faulty paper control PCA. At least one of two tabs must be present. 3. Message: 06 Typeface List HP LASERJET 4, 4M, 4plus, 4mplus, 4Si, 4Si MX, 4p, 4mp printers 06 Typeface List HP LaserJet 4, 4M, 4Plus, 4Mplus, 4Si, 4Si MX, 4P, 4MP printers Press Continue to have the printer print from the other tray. check over here

A broken tooth on one gear is all it takes. The PostScript option requires a minimum of 4 MB for proper operation. Measure between the two heavy gauge pins on the fuser assembly connector. Reduce the document's complexity by using fewer fonts and removing bolding, shading, or underlining. 2. http://www.csgnetwork.com/hplaserjeterrors.html

Hp Laser Printer Error Codes

Turn printer off, and then back on. Contact your dealer or HP Service Technician. If the message returns replace toner cartridge.

X description: 1 = Beam-detect error 2 = Laser error Press GO. Replace PS1 if defective. Incompatible memory card in front slot 57-2 error. Hp Inkjet Printer Error Codes This is performed by holding down the online key while turning the printer on.

Paper Tray is overfull 2. Hp Printer Error Code List Pdf On the left end of the assembly you will see the ceramic lamp end with a white wire connected to a terminal. If it's broken, you will need to replace the sensor flag. Message: WM Job 300 HP LASERJET 4, 4M, 4Plus, 4MPlus, 4SI, 4P, 4MP Printers WM Job 300 HP LaserJet 4, 4M, 4Plus, 4Mplus printers The job was printed at 300 dpi.

Message: W4 Job 300/Off, HP LASERJET 4, 4M, 4SI, 4P Printers W4 Job 300/Off HP LaserJet 4, 4M, 4Si, 4P Printers The job was printed at 300 dpi with page protection 52 Scanner Error Hp Laserjet Clear message by pressing SHIFT and Continue on the printer. On the 5L, set the Enhanced I/O to AUTO (PCL mode) and resend the print job. IIISi/4Si Only: 1.

Hp Printer Error Code List Pdf

The laser shutter operation is functioning improperly. Source If there is paper in the tray and the printer still displays 11, verify the tray is all the way in. Hp Laser Printer Error Codes Watch the movement of the gears. Hp Laptop Error Codes Note II: Short C211 on the DC Controller to bypass Error 50 time delay. (The printer must be turned off.) Note IID: Short C216 on the DC Controller to bypass error

Bad drive gears. http://softacoustik.com/error-code/laserjet-error-codes-service.php If error is gone replace each EIO device until error appears. Many times, although not resulting in an error 50, the upper fuser roller simply becomes worn, the teflon coating begins peeling and a vertical line(s) can result on the printed page. Replace as needed IIP S/N between 2925J00000 and 3047J99999 replace fuser assembly Back back to top How did we do? Hp Computer Error Codes

The printer can be operated until service repairs are made. Recycle printer power. On the right side of the fuser is a set screw - look in the area of the cover latch. http://softacoustik.com/error-code/laserjet-iip-error-codes.php Defective MIO Card - Replace card Defective Formatter Card - Replace card Back back to top How did we do?

Reseat cables to the laser/ scanner and engine controller. 4. 50.0 Fuser Error Hp Laserjet P1102 Please try the request again. If the paper isn't picking up out of the paper tray, visually inspect the pickup roller.

If the error appears again, repair service is required.

Replace if defective An abnormal connection break may have occurred during data transfer - Press Continue or Go to clear this error message. Remove the page from the output tray and press Continue. Remove excess paper and press Continue. Hp Error Code Oxc4eb827f Top cover open. 2.

III, IIID Only: 1. 53-1 Error in front memory slot. - Replace memory card. 2. 53-2 Error in rear memory slot. - Replace memory card. Load the correct paper tray and/or media or press continue to use the media in the installed tray. Defective Paper Control PCA on the Paper Feed Assembly. 4L Only: 1. have a peek at these guys Low/unstable power (low line voltage, brownout condition).

Error 18 MIO Not Ready The printer is not connected to a Lan. Misadjusted or bent Switchback Assembly. We don't sell hard drives, monitors, software, mp3 players, or the zillions of other computer products sold by every other cookie-cutter website.