Also check motor cable connections. On some models pressing the Continue button on the control panel will resume operation. Check paper tray for overfull condition. The chip may be missing or defective or contain incorrect information. check over here
The first location is just above the AC inlet either on the P/N label RG1-1782 or to the left of the label. See page G-7 of the User's Manual. 61.1 Error61.2 Error61.3 Error61.4 ErrorIIISiA SIMM that is the wrong size or speed is installed. Populating a Keyword field 3. Then press the "FORM FEED" key and then the "ENTER" key. http://fixyourownprinter.com/posts/24948
Power cycle the printer. A buildup of toner on the edges of the tray which slide into the printer can sometimes cause problems. If the error is still present, switch the printer off and remove the SIMM board If the error message does not appear, the problem is on the SIMM. It displays an error saying "50 -Service" I have been told already that this means that I have to change my fuser.
Check the paper path for toner or paper dust buildup. The transparency feeds slowly through the printer. The error 10 indicates a problem with the printer obtaining the information from this chip. Hp Printer Error Code List Pdf Bad paper exit sensor.
It is important for proper grounding. Use saved Parts Lists as templates to create new lists. The computer is a 486 using WP 6.1. http://www.all-laser.com/aerror-code/ Bad component(s) 11 Paper Out (MP/PC/UC/LC/EC/LE LOAD) All printers 1.
On the 4/4M/4+ and 5: The print job is to complex, enable page protect from the control panel and from the software. Hp Error Code Oxc4eb827f Google does not endorse, and expressly disclaims liability for any product, manufacturer, distributor, service or service provider mentioned or any opinion expressed in answers or comments. If it is a memory SIMM with more than one bank of memory the good bank will be configured. ERROR 51 - Service Improperly seated toner cartridge - remove and reinstall Laser shutter blocked or damaged Damaged fiber optic cable Defective Laser PCA - replace I/IID/III/IIID Defective toner cartridge -
Try with SIMMs or font cartridge removed to be sure error clears. 2. http://printcopy.info/?l=en&mod=free&chap=erc&brand=HP&model=LaserJet%20IIIP Four megabyte cards go in first from bottom slot up, then one megabyte cards. Hp Printer Error Codes List Turn the printer off and verify the optional interface card is installed correctly. Hp Computer Error Codes Replace the fan.
Could be a bad cable or loose connection or just a poor quality cable. http://softacoustik.com/error-code/list-of-error-messages.php If the board becomes defective, you will receive an error 12. Reassembly went fast. Press and hold the Go button for 10 seconds. Hp Inkjet Printer Error Codes
On the II and III Series printers, this error message can be caused by a faulty paper control PCA. If error persists you will need to replace the formatter PCA. If the error persists, consult service. 53.XY.ZZError 534, 4M, 4Plus, 4Mplus, 4Si, 4Si MX, 4P, 4MPAn error occurred during configuration and validation of SIMM memory. http://softacoustik.com/error-code/laserjet-4-error-messages.php You can reseat the connectors to the scanner assembly and the control board.
If it measures as an open circuit the lamp or thermal fuse is burned out (these parts are connected in series). Hp Officejet Error Codes Reset as needed. If the rollers are glazed or you see cracks, replace the roller or assembly.
Make sure the paper cassettes are installed correctly and adjustments are set properly. Remove all EIO devices and firmware DIMM if installed. on LJII short C211 on DC controller PCB to bypass 20 minute delay. Hp Printer Error Code 0x610000f6 If the error remains, it is most likely that the fuser itself (thatís the green felt-covered rectangular box which can be seen when the printer latch is open) is burned.
This page lists all error codes for Laserjet 4V and older printers: http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?locale=en_US&taskId=110&prodSeriesId=25489&prodTypeId=18972&objectID=bpl04079 HP LaserJet 4V Series Printers (and Older) - Printer Control Panel Display Status and Error Messages Error 52 Back back to top How did we do? Remove the card and reseat it, try swapping with a know good card from another printer. http://softacoustik.com/error-code/kitchenaid-error-messages.php Improperly seated SIMMs or font cartridge - remove, check/clean contacts re-install and try again.
I checked the HP web site for current model printers and most do not have drivers for any Windows Operating System pre: Windows 98. Follow these steps: Load a transparency in the priority input tray. This is a very common failure on the laserjet IIP/IIIP, Apple Personal Laserwriter, QMS PS410 and other Canon LX engine printers. Again on the LJII/III we are starting to see more and more failures of the gear drive assembly.
Is the software set for the size you're using? In either case, our 52 error kit contained in our printer repair kits section will most likely fix the problem. Power cycle the printer. Turn the printer off for 20 minutes to clear the temporary 50 error.2.
May require add'l memory 4L Too much data or data too complex, simplify the print job Turn image adapt and page protect to ON or AUTO (Can be set through HP