Home > Error Codes > Lexmark Optra T620 Error Codes

Lexmark Optra T620 Error Codes

Contents

Check the continuity of the fuser lamp at the two heavy leads. Make sure fuse is installed correctly, Verfy proper fuser is being used. Error 63 Unformatted or Defective Disk The printer will ignore a disk it senses as defective. Replace Printhead Pricing Error 936 Error 937 Error 936/937 Main Drive Motor, Transport Motor An error with the main drive motor has been sensed by the printer Optra s 2450 Optra news

Error 43 Font card format not supported by printer. Check for correct location of the jumpers on the interconnect board for the model/type printer you are servicing. San Rafael, CA Great that you have that part in stock and thank you for your quick reply. Remove jammed media Error 90X Software Error Unrecoverable software error. http://www.manualslib.com/manual/482154/Lexmark-T620.html?page=30

Lexmark Error Codes

If the paper is not jammed in the duplex unit, then it may be jammed in the rear of the printer. We can email further info if needed for your particular model. Make sure there is no paper jammed in the printer. Error 122 Fuser Error - Problem in the fuser, not heating, heating to quickly or too hot.

Transfer Roll Error Cannot start servo operation. Error 29 The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22. Il ya eu une erreur à l'application. Error 37 37 Insufficient Collation Memory Memory is too full to collate the print job.

Hide thumbs Also See for T620 Setup manual - 38 pagesQuick reference - 2 pagesTroubleshooting - 1 page 1 2 3 4 5 6 7 8 9 10 11 Lexmark Support Additional info on X and XX codes available by email. POR several times Check each board for secure ground. Error 59 Duplex Cover Open Top cover of duplex unit is sensed open.

Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input Error 52 Flash Full - Not enough flash memory for data requested to be stored. Make sure the memory shown on the printout matches the installed memory. If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages.

Lexmark Support

Check Toner Sensor Check Cable Check System Board Check developer drive for worn, loose or broken parts. Houve um erro com o aplicativo. 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms Lexmark Error Codes To print the manual completely, please, download it. Se ha producido un error en la aplicación.

It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. http://softacoustik.com/error-codes/lexmark-z22-error-codes.php Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it Error 44 Defective font card installed in font slot. de Wir entschuldigen uns für die Unannehmlichkeiten.

Reload the paper and do a power on reset. Can be system board or printhead. fr Nous sommes désolés pour ce désagrément. More about the author Error 54 Serial Error - Framing or parity error on serial.

If cables, connectors and connections are good replace assemblies listed. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is Replace printhead, system board or ribbon cable.

Es gab einen Fehler bei der Anwendung.

Works great and certainly solved the problem (as I expected it would). -Alan A. Error 920.X and 922.XX may display for a cold fuser. Check fan connector and cable for loose or damaged connection. Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person.

Sign up! John D. See “Duplex” on page 2-16 Error 24 The defined paper size is too short to print data as formatted. click site Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller.

Go to the "Input Tray(s) Option Service Check" on page 2-69. Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation. Reconnect. Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes.