Home > Fuser Error > Laserjet 4100 50.2 Fuser Error

Laserjet 4100 50.2 Fuser Error

Contents

Is there another part that now needs to be replaced in the fuser? RE: fuser error with a good fuser hpwizzard (IS/IT--Management) 6 Jan 10 10:32 Yes, in case the fuser is tested to be OK along with the fuses i the PSU I Covers parts: RG5-2661 C4118-69001 C4118-69011 RG5-4283 RF5-1885 RG5-3718 Category Science & Technology License Standard YouTube License Show more Show less Loading... by unknown on May 12, 2006 at 8:02am Add comment Please sign in to comment 0 There is a tube of the grease on this site. check over here

FIX Service 25,557 views 12:08 Hp LaserJet 3015 - How to repair - How to fix - 57.04 Fan ERROR - Duration: 9:31. Converts 240V to 120V. RE: fuser error with a good fuser mufka (ISP) (OP) 4 Jan 10 18:31 Fuses are ok. I can get a cheap power converter for "light use" that's fuse protected for about $10. http://www.printertechs.com/printer-troubleshooting/11-50-2-fuser-error

50.2 Fuser Error Laserjet Pro 400

Working... That one on eBay is a good deal. Sign in Statistics 3,236 views 2 Like this video? Maybe replacing the entire unit would be more feasible?

It has two internal fuses where one is for the fuser heating element (F1). same error. Rating is available when the video has been rented. What Is Fuser In Printer I doubt it will go up much in price.

precisionroller 124,050 views 12:19 Toner Cartridge Printing Defects: Causes and Solutions - Duration: 21:44. Fuser Error Hp Printer You may also want to check your page count or just look at the pickup and separation roller since sometimes it is better to order the maintenance kit which include some Loading... Loading...

Where can I get a diagram of the printer ? 50.3 Fuser Error Don't replace: rejuvenate! Rating is available when the video has been rented. Cheaper than buying a new fuser.

Fuser Error Hp Printer

by dmzcompute on Nov 12, 2005 at 8:00pm Add comment Please sign in to comment 0 Just spotted this.

No job for an amateur. 50.2 Fuser Error Laserjet Pro 400 I do not know if good or bad, but if it works, it is what you need.http://cgi.ebay.com by dmzcompute on Nov 12, 2005 at 8:41pm Add comment Please sign in to 50.2 Fuser Error Hp 4525 Email me for pricing and ordering info.

The early models had a fuser problem too, the films shredded. check my blog Brian by Brian on Dec 15, 2004 at 7:05am Add comment Please sign in to comment 0 Thanks for your hint ! Continue holding the buttons until the message says reset maint count you can then let up on the buttons.As to the 50.2 error you are getting bad fusers, IF when you The right edge of the fixing film on the fuser roller had deteriorated, resulting in jagged edges in the film. (That end looked browned, like the heating element was hotter at 50.2 Fuser Error P4015

Watch Queue Queue __count__/__total__ Find out whyClose HP Laserjet Pro 400 - How to repair - 50.2 Fuser error erepairer SubscribeSubscribedUnsubscribe Loading... Registration on or use of this site constitutes acceptance of our Privacy Policy. They will run on either 120V or 240V depending on your country. this content I've tried another fuser....same error.

These machines draw a lot of power so they should never be plugged into a power strip with other devices, battery back up, and make sure there are no other large 50.1 Fuser Error I have purchased a maintance kit from hp directly when it said to maintence the machine and now the fuser error message is appearing. Cancel Red Flag SubmittedThank you for helping keep Tek-Tips Forums free from inappropriate posts.The Tek-Tips staff will check this out and take appropriate action.

Sign in to report inappropriate content.

Get a fuser film ASAP and remember the lubrication grease tooRegardsTrev by inkjets on Jul 27, 2005 at 8:36am Add comment Please sign in to comment I had checked the two I go with suggestion above that the clips on one end or the other are not fully seated or not making contact correctly. I have a spare film here and may try that as I've nothing to lose, only problem is that I do not have any PFA Grease. 50.2 Fuser Error 4200 Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc.

Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... I have a hp4000 tn and i am getting this error message. I'm surprised it works at all. have a peek at these guys Click Here to join Tek-Tips and talk with other members!

By joining you are opting in to receive e-mail. I think we're going to go for a new or refurbished printer. If that does not work, replace the Fuser. 2. When the fusing unit was reinstalled into the printer, the printed displayed the 50.2 FUSER ERROR message.I swapped the fusing unit with another one and no FUSER ERROR displayed so the

Reply With Quote 11-29-2006,04:21 PM #4 Strider View Profile View Forum Posts View Blog Entries View Articles Member Join Date Feb 2006 Location Akron Ohio Posts 99 The 50.2 error means RE: fuser error with a good fuser hpwizzard (IS/IT--Management) 6 Jan 10 13:53 Yes, there should be two fuses in the PSU part of the ECB. BrokenPrinter1 305,601 views 10:49 HP Color LaserJet 4600 Maintenance Kit Instructional Video - Duration: 9:12. What does the fuser and the knobs you turn look like?

Learn How to Post and More  Community News  Best of the Community Blog  Notebooks Notebook Operating System and Recovery  Notebook Boot and Lockup  Notebook Wireless and Networking  Notebook Audio  Notebook Video, Watch QueueQueueWatch QueueQueue Remove allDisconnect Loading... Kevin For More information involving Printer Repair take a look at this site: http://www.fixyourownprinter.com/ Related posts:41.5 Printer Error- HP LaserJet 4000, 4050, 4100 Light Print -Laser Scanner Repair - HP Laserjet None of the printing supplies companies sell it themselves, just the components.

The printer uses much more power then they provide. Respond to this 0 Error 50.2 is a fuser warmup problem, most likely you've got an Engine controller board failure, the ECB switches the fuser on and off. This content is provided “AS IS” and is subject to change or removal at any time. I reset the maint counter as described above but am still getting the error message.