Home > Fuser Error > Laserjet 4100n Fuser Error

Laserjet 4100n Fuser Error

Contents

The printer still gives the 50.2 error messege. This is the unit that gets hot and fixes the toner onto the paper just before the paper exits the machine. BrokenPrinter1 29 488 visningar 8:28 HP LaserJet 4000, 4050, 4100, 5000 Scanner - Längd: 5:03. Something about endplate angles being wrong. this content

Then flip the fuser over to the right side (the non-gear side) and press in on the other fuser tab to make sure it is also fully clicked in place. (right Privacy Policy Terms of Use Laser Printer Repair and Fax, Copier Service ArticlesThis Website is Dedicated to Providing Free Service and Repair Articles Designed to Help Service Technicians or End Users Logga in och gör din röst hörd. VisningsköKöVisningsköKö Ta bort allaKoppla från Läser in ...

50.2 Fuser Error

One customer got his in 3 days, the other 4. Best thing to do is just replace the fuser. Moose Scrapper 714 383 visningar 4:30 Kit 2300 - Kit Hp 2300 - Kit Mantenimiento 2300 - Längd: 10:09. Any ideas what to check?

BrokenPrinter1 79 278 visningar 12:29 HP Laserjet Jet Direct Card Install Uninstall - Längd: 3:18. Arbetar ... Help this question get an answer by entering the correct category or product below. 50.2 Fuser Error P4015 Thanks again, for all the support.

I have never had to open up the fuser before on these printers. THANKS again for your input. This content is provided “AS IS” and is subject to change or removal at any time.

Somehow, it's a little different from the diagram.All the connectors seem to stay plugged tightly (it was working fine yesterday, just displays that message today without anybody touching its inside).

Kit Hp 10 371 visningar 5:37 HP4000/4050/4100/5000 Network config - Längd: 1:48. Hp Printer Fuser Error Extension Quick Bytes Technology Learning 54 252 visningar 13:08 CONFIGURAR IP LASERJET 4000/4050/4100/5000 - Längd: 3:23. Läser in ... Pull the fuser straight back and out of the printer.Hopefully, this article has helped you troubleshoot the 50.2 fuser error in your HP laserjet 4000, 4050, and 4100.

50.2 Fuser Error Laserjet Pro 400

Laddades upp den 10 apr. 2009http://www.fastprinters.com/hp_fuser_...Installation instructions on how to replace the fuser, transfer roller and pick rollers on the HP 4100 LJ Laserjet printers. http://fixyourownprinter.com/posts/30652 by dmzcompute on Jul 27, 2005 at 9:29am Add comment Please sign in to comment Thank you both for your replies. 50.2 Fuser Error Someone suggested the main board replacement, but it's expensive, is it worth it? 50.2 Fuser Error Hp 4525 What are the odds of that?

Or just drag it here! news Also, the Engine Controller is another option but after working on several hundred of these machines and only replacing one on a 4100 I'll say that very rarely happens. HP 4000/4050 Fuser Assembly RG5-2661-000 HP Fuser for LaserJet 4100Troubleshooting The HP Laserjet 4000, 4050, and 4100 50.1 Fuser ErrorFirst thing to try in troubleshooting the HP Laserjet 4000, 4050, and Any help to fix it would be much appreciated. What Is Fuser In Printer

If the problem is not related to the Fuser, replace the Engine Controller Board Conclusion About the  HP Laserjet 4000, 4050, and 4100 50.2 Fuser Error MessageYeah, that last  section was MP A 50.4 code is bad line voltage. Site administrator www.printertechs.com Reply With Quote Quick Navigation Hewlett Packard Laserjets Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Printer Forums Hewlett Packard Laserjets All have a peek at these guys If the message   persists, reseat the Fuser.

Logga in om du vill rapportera olämpligt innehåll. 50.3 Fuser Error I changed out the fuser and still getting that message. by Anonymous on Feb 19, 2010 at 1:37am Add comment Please sign in to comment 0 Hi, I'm getting 50.2 Fuser Error.

Läser in ...

You'll either see two shiny screws in a white plastic face plate, or you'll see two blue elongated 'knobs' that swivel on a pin, thereby unlocking the fuser so you can Covers parts: C8057A C8057-69001 RG5-5063 RG5-3718 RF5-3114 RG5-5295 Kategori Vetenskap och teknik Licens Standardlicens för YouTube Visa mer Visa mindre Läser in ... If the problem is not related to the fuser, replace the enginecontroller board. 50.1 Fuser Error Cheaper than buying a new fuser.

Rankning kan göras när videoklippet har hyrts. Converts 240V to 120V. Does anybody kow where I can source this stuff in the UK? check my blog Hence, why I don't work on my own car.To answer your question, if you open the top cover where you slide the toner cartridge in, you'll see how the paper goes

Powered by vBulletin Version 4.2.3 Copyright © 2016 vBulletin Solutions, Inc. Logga in och gör din röst hörd. I did not notice that the connection had slipped out of place, probably when I was rotating the gears to view all of the fuser roller. I will return the used fuser and get a new one and rule that out before doing anything else.

Logga in och gör din röst hörd. Arbetar ... Could it be that the power outlet is not providing enough power to the newer ones but the old one is fine? Thanks by unknown on Oct 27, 2005 at 8:26am Add comment Please sign in to comment 0 Please ignore above post.Thanks for your help I have indeed taken out the fuser.

However, it is an expensive job and quite complicated. Logga in om du vill lägga till videoklippet i en spellista. What does that mean Loose fuser tabs on the HP LaserJet 4000/4050/4100 - a potential 50.2 error If you experience a "50.2" fuser error while using a LaserJet 4000, 4050, or Scholar: An expert who has written 20 answers of more than 400 characters.

to let the error code reset)When it starts warming up give it a few seconds,then turn it off and back on.This will let it warm up some so that the warmup by Anonymous on Feb 18, 2010 at 8:19am Add comment Please sign in to comment Assuming the used fuser was good, the only other thing that would cause the error would Shubham Chugh 294 328 visningar 2:56 Reparación de fusores de impresoras HP - Längd: 3:24. Under the instructions to replace the fuser  is a link to purchase a fuser.

What Brian is talking about is the main Engine Board which is sandwiched between the top and bottom half's of the printer.