Home > Fuser Error > Lexmark 200 Fuser Error

Lexmark 200 Fuser Error

Contents

Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. Taal: Nederlands Contentlocatie: Nederland Beperkte modus: Uit Geschiedenis Help Laden... Reload the paper and do a power on reset. It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer. news

Contact service person Error 940 LV Power Supply Low voltage power supply cross over test failed. Paper jam in the manual entry area 4. Error 24XPaper Jam - Check Tray "X"1. For additional fusers on promotion, click here. http://support.lexmark.com/index?page=content&id=SO1583

Lexmark Error Codes

Check fan for binding or defective bearing - Replace Fan How did we do? Can be system board or printhead. The installed print cartridge is not supported by the printer.Replace the Print cartridge. For additional re-certified laser printers, click here.

Los Altos Hills, CA Thank you. Error 27 Envelopes/paper loaded are wrong size. Log in om deze video toe te voegen aan een afspeellijst. Lexmark Error Codes Problem Replace the Print cartridge.

Perform fuser service check. 2. Error 925A 925 service error indicates the fuser lamp rating does not match the printer code.1. Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is dig this If the Quick Disk Test passes but the disk does not work, run the Disk Test / Clean (2 hour test).

Use caution when measuring AC voltages. Service Fuser Error Lexmark Printer If you have other tech support questions that are not covered here, send email to [email protected] Turn the printer off and turn on after two minutes. 2. Replace the system board.

Lexmark Printer Error Messages

There should be zero ohms resistance between the transfer roll shaft and the high voltage supply contact.

Replace the main drive motor. Lexmark Error Codes The fuser can usually be removed with two simple screws and the entire assembly lifted out. Lexmark Fuser Error We got it this morning and I have it installed.

Additional info on X and XX codes available by email. http://softacoustik.com/fuser-error/lexmark-922-fuser-error.php Don't show me this message again. For additional fusers on promotion, click here. Error 930The wrong printhead is installed.Replace the printhead. Lexmark Engine Error

If there is no paper jammed in the duplex unit, then it may be jammed in the rear of the printer. Inspect for chafing or damage to ribbon cable at sharp bends around rear cover 2. Replace bump motor 6. More about the author Error 927Main Fan, Cartridge Fan or RIP fan stalled.Replace Fan Unit Error 928Erase lamp assembly missing or disconnectedReplace Erase lamp assembly Error 929The toner sensor is defective, the developer drive assembly

Error 52 Flash Full - Not enough flash memory for data requested to be stored. Lexmark Printer Error Lights Is the cable damaged? "Fuser drive 4-61. "Fuser assembly 4-60. Error 923 Fuser is too hot while printing or when idle. • Short in the thermistor circuit. • Noisy thermistor signal • Fuser is actually overheating due to hardware faults.

Transcript Het interactieve transcript kan niet worden geladen.

Make sure the memory shown on the printout matches the installed memory. Replace the LVPS (low voltage power supply) HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Error 923Fuser is too hot while printing or when Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. 938.06 Service System Electronics Error 924924 Fuser Error - Open circuit detected in thermistor circuit.

Go to step 3. Weergavewachtrij Wachtrij __count__/__total__ Lexmark E260, E360, E460, X264, X363 Fuser and Heat Errors (920 - 925) iteminc AbonnerenGeabonneerdAfmelden698698 Laden... Indicates that the fuser is below standby temperature when the printer is idle. click site Remove and reinstall print cartridge. 2.