Home > Fuser Error > Lexmark X646e Fuser Error

Lexmark X646e Fuser Error

Contents

Replace the Autocompensator Assy. Personally, I never got a Lexmark printer to work doing this, but this is in the manual. Check the left and right transfer roll arm assembly to make sure it is fastened and locked in the down position if applicable to your machine. Error 25 Input sensor made at wrong time. http://softacoustik.com/fuser-error/lexmark-fuser-error-136.php

If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages. Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation. If the error message goes away with the old fuser unit, please check that the new fuser unit is the correct one for this printer model. It may take the printer 10-20 seconds to determine if the print cartridge is defective.

920.06 Service Fuser Error T644

Gustavo Segura 3.219 προβολές 4:05 Lexmark E260, E360, E460, X264, X363 Fuser and Heat Errors (920 - 925) - Διάρκεια: 14:14. I would not recommend doing this yourself if you haven't done this before, take it to a repair shop. Transfer Roll Error Cannot start servo operation. The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure.

Error 37 37 Insufficient Collation Memory Memory is too full to collate the print job. POR several times Check each board for secure ground. If this won't help, and the printer is under warranty, you should log it in with the servicing company.If the printer is out of warranty, your next option is to change 922.02 Service Fuser Error Open the printer rear door to access the jam.

Recep Kalayci 26.994 προβολές 29:52 Sustitucion de Kit de mantenimiento X646 Y X644 - Διάρκεια: 9:12. See “Network Wrap Tests” on page 23. Tell us some more! If this does not clear up the fuser error, the problem may be in one of the following: the fuser cover assembly the engine board the DC fuser cable the fuser

ERROR 22 The exit sensor was not unmade in time. Service Fuser Error Lexmark Printer Fortunately, replacing fusers on these models model is not difficult.  We have installation instructions available here. You have to take the printer to a servise centre for replacing Fuser. Posted by soyamor on Jan 24, 2011 Want Answer 0 Clicking this will make more experts see the question and we will remind you when it gets answered.

920.06 Service Fuser Error T654

There was an error with the application. View Most Popular T644 Laser Printer Printers & Copiers Related Question I have an error message 120.10 service fuser error, what does this mean?...Service Fuser Error appears when the fuser does 920.06 Service Fuser Error T644 Lexmark Fuser Pricing Error 925 A 925 service error indicates the wrong fuser lamp is installed in the printer and does not match the one stored in the printer code. 920.06 Service Fuser Error T652 Power strips and uninterrupted power supplies can cause a low amperage problem in your printer which can trigger a false fuser error.

Verify correct cable connections from the Engine board to the HVPS. my review here Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on test). Jump to error 92X Some Lexmark printers have indicator lights which indicate by solid, blinking or off, an error condition. Lexmark 924.01 Service Fuser Error

that the fuser unit failed to reach the standby temperature. I will have purchasing call in an order. Purchasing information:  Lexmark T640 , T642, T644 series fuser and maintenance kitPurchasing information:  Lexmark T650 , T652, T654 series fuser and maintenance kit Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, http://softacoustik.com/fuser-error/lexmark-922-fuser-error.php If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed.

If it is under warranty, repair will be done at no cost Jan 18, 2010 | Lexmark E450dn Laser Printer 1 Answer Lexmark E342n Laser Printer Fuser Error 920 Fuser Error Lexmark T640 Fuser Replacement Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. The fuser is the main part of a printer maintenance kit.

Error 38 38 Memory Full Memory used to store pages is full.

We can email further info if needed for your particular model. It can also be the LVPS (low voltage power supply) or a fuse in the power supply on some models. Replace printhead, system board or ribbon cable. Lexmark X654de Service Fuser Error Check printhead, cable, motor, system board.

Or you will need to replace the actual fuser assembly. unfortunately you can't just remove/clear the error. Replacement of the thermistor is not a cost effective repair, replace fuser assembly. navigate to this website Order all your Lexmark printers, parts and supplies online at fastprinters.com Kit part number 40X0100 includes Fuser 40X2592 or 40X0116, pickup tire 40x0070 or 99A0070, transfer roller 99a1015 and charge roller

Learn more You're viewing YouTube in Greek. Check fan connector and cable for loose or damaged connection. Your answer needs to include more details to help people. http://support.lexmark.com/index?page=content&id=SO4745&actp=search&viewlocale=en_US&userlocale=EN_US&segment=SUPPORT&productCode=&searchid=1275926294153 If you are technicall inclined and want to try changing the fuser, you can look online for a service manual...they are usually available for a fee.