Action Press (Select) to continue. If the above action does not solve the issue, contact HP, or contact an authorized service provider. Tech Support Support Home PageMaintenance Kit InstructionsOther instructionsTroubleshootingArticles, news, blog Featured Articles HP Error CodesEntering Service ModeService mode PIN codesCounterfeit parts challengeCold reset instructionsClearing maintenance countJetDirect Reference GuideHalf-way testRepetitive defect rulerTestimonialsInnovations The stapler/stacker LED blinks in amber. 13.12.08, 13.12.09, 13.12.10 and 13.12.11 Jammed in the output device Jams in the output device (stapler stacker of stacker). check over here
This most likely means that there is a piece of paper wrapped around the fuse. This high performance printer was designed to quickly and efficiently print large size documents with print engine speeds of up to 35 pages per minute. Figure 1: Opening top cover and removing print cartridge Use the green handle to lift the paper-access plate. part# RM1-0013 purchase HP 4200 fuser/maintenance kit here for use in HP LaserJet 4200, HP LaserJet 4200N, HP LaserJet 4200TN, HP LaserJet 4200DTN, HP LaserJet 4200DTNs, HP LaserJet 4200DTNsl part# RM1-1082
The EIO accessory might be defective. Figure 20: Opening rear-output bin Remove the fuser by pushing up on the blue tabs and check for paper in the printer as well as in the fuser. Press the (Up Arrow) button and the (Down Arrow) button to step through the instructions. If the message persists, contact HP Customer Support.
Interval 200,000 pgs 200,000 pgs Service PIN 11420002 11420002 HP LaserJet/Laser Printer Repair Parts Fuser, 110v RM1-0013 (4200) In Stock Maintenance Kit, 110v Q2429-67905 (4200) In Stock Reinstall the stapler/stacker or stacker. Laser 4200 52.2 Laser Scanner Rotation Error 53.XY.ZZ PRINTER ERROR There is a problem with the printer memory. Hp Laserjet 4250n 49.4c02 Service Error Set the output bin cover aside.
If possible, print to another network printer to verify the network is working correctly. When handling DIMMs, either wear an anti-static wrist strap or frequently touch the surface of the DIMM anti-static package, then touch bare metal on the printer. top 56.1, 56.2 PRINTER ERROR To continue turn off then on Description Unknown input/output device installed. Figure 34: Turning off and unplugging the printer Turn the printer so that its rear cover faces you.
The consumable management features will be lost (such as the gas gauge, cartridge page count, estimated pages remaining, etcetera) and the control panel may report that the printer has a non-HP 13.98 Paper Jam An improper communications protocol might be in use. Re-install the plastic rear output bin. To view Help for a message (if available), press (Help).
An improper communications protocol might be in use. 22 PARALLEL I/O BUFFER OVERFLOW The HP 4200 printer's parallel buffer has overflowed during a busy state. 40 EIO X BAD TRANSMISSION The http://www.printertechs.com/printer-troubleshooting/370-13-20-error-on-hp-laserjet-4200-or-hp-laserjet-4300-series Continue to hold down the checkmark (Select) button until all three LEDs are illuminated. 5. Hp Laserjet 4250 Error Codes If the error persists, contact HP support. Hp Laserjet 4200 Cartridge Installed Message top 49.XXXX PRINTER ERROR To continue turn the printer off then on Description The printing operation has been aborted.
Make sure that the accessory is properly seated on and connected to the printer, without any gaps between the printer and the accessory. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. CAUTION: Static electricity can damage DIMMs. Hp Laserjet 4200 And 4300 Series Printers Drivers
If you cannot find your product on this site, go to HP Support Center - Hewlett Packard Enterprise. X Description 3- EP cartridge fan, right side (HP LaserJet 4300 only) 4- Main cooling fan, left side Action Turn the printer power off and then turn the printer power on. alternates with 68.X PERMENANT STORAGE ERROR To continue press (Select) 68.X PERMANENT STORAGE FULL For help press ? this content A tray [X] that was opened or filled is trying to lift into position, but there is an obstruction in the tray.
The deflector is behind the rear output bin door and is made of black plastic. Hp Laserjet 4250 Error 13.01.00 Jam In Tray 2 If the above action does not solve the issue, contact HP or authorized service provider. If the message persists, replace the duplexer.
TheRealDrBullshit 36.306 προβολές 28:19 How to repair hp laserjet p4015 p4515 fix paper jam problems - Διάρκεια: 5:35. top 51.XY PRINTER ERROR For help press ? precisionroller 93.539 προβολές 7:09 How To Replace The hp Laserjet 4200n 4250n 4350n Swing Plate PART 1 - Διάρκεια: 5:50. 13.20.00 Jam Inside Rear Door alternates with 55.X PRINTER ERROR To continue press (Select) 56.1, 56.2 PRINTER ERROR To continue turn off then on 57.X PRINTER ERROR To continue turn off then on 57.7 DUPLEX FAN
Reinstall all paper input trays. Reinstall the cartridge and close the top cover. Figure 46: Pulling the cover on the right side of the printer Remove the cover from the printer. Once you have correct fuser matched up with your model, install the replacement fuser by inserting it and aligning the left side first.
The stapler/stacker LED blinks in amber. 13.13.00 Jam inside duplexer A paper is jammed inside the duplexer.LaserJet 4200 13.10.00 Fuser Jams a paper jam exists in the fuser area. The spring can break causing the motor assembly to not properly engage the gear on the tray. As a safety precaution wait 30 minutes for the fuser to cool before proceeding. If the above action does not solve the issue, contact HP or authorized service provider.
Use (Up Arrow) or (Down Arrow) to scroll to INFORMATION, and then press (Select). top 68.X PERMANENT STORAGE ERROR For help press ? Make the page contents less complex and resend the print job. NOTE: Do not force the paper if it will not move easily.
Figure 52: Setting bottom of cover onto the printer Slide the cover toward the front of the printer until it clicks into place. Remove all memory DIMMs or third-party DIMMs from the printer. (See the printer User's Guide for information about removing DIMMs.) Remove all EIO devices from the printer. (See the printer User's