Home > Hp Laserjet > Laserjet 4050 45.1 Error

Laserjet 4050 45.1 Error

Contents

However, if you work through the steps above in this article you can hopefully,  diagnose the 41.5 printer error. by unknown on Jan 7, 2010 at 7:49pm Add comment Please sign in to comment 0 Oh my Gosh is this thread still going!?!?!! See The substrate-advance sensor is not working. Please join our friendly community by clicking the button below - it only takes a few seconds and is totally free. check over here

Second and the most common one I see is the feed assembly behind the tray 1 pick up assembly. Tray 2 and 3 cant even print single sided. printer worked fine till yesterday 5/4/11. Uploaded on Feb 5, 20082008 Stuart Woods Category Science & Technology License Standard YouTube License Show more Show less Loading... http://www.fixyourownprinter.com/posts/25076

Hp Laserjet 4000 Error Codes

by dmzcompute on Nov 30, 2004 at 2:50pm Add comment Please sign in to comment 0 I had this same issue and it turned out a staple was wedged in the Seems the clutch on the assembly will sometimes fail to engage, causing a 41.5Part # RG5-2651-090CNBagger by Bagger on Aug 12, 2005 at 8:23am Add comment Please sign in to comment by unknown on May 12, 2010 at 9:13am Add comment Please sign in to comment 0 I know this thread has been going on for 5 1/2 years, but thank you Respond to this 0 Yeeeees but........Glad it worked for you.

by unknown on Mar 2, 2012 at 8:48am Add comment Please sign in to comment Thanks for keeping this thread around, and for all the detailed solutions!I replaced the toner cartridge I changed the paper delivery assembly and also the fuser. by robnjay on Mar 9, 2009 at 7:33pm Add comment Please sign in to comment Thank you so much for posting this. Put roller back on, the blue tab goes last.

First you want to try to feed media from the manual feeder and see if it works ok. If the 41.5 printer error doesn’t happen from tray 1 then best bet is to replace the feed assembly. Press the clip, swing the plastic back on its hinge.

by dmzcompute on Sep 22, 2006 at 3:46pm Add comment Please sign in to comment 0 hey dmz thanks by unknown on Nov 6, 2006 at 8:34am Add comment Please sign

by unknown on Jul 2, 2014 at 9:01pm Add comment Please sign in to comment 0 That doesn't make sense. by Trev Pearson on Oct 1, 2003 at 4:20pm Add comment Please sign in to comment 0 Hmmm....If you'd searched our archives for 41.5, you would have seen that covered more and 13.xx errors. It has a "L" arm and is attached with a spring in the rear which keeps the "L" arm away from the center of the selenoid.

Rg5-2651-090cn

Define grabs too many pages. http://www.fortwayneprinterrepair.com/wordpress/2011/11/06/41-5-printer-error-hp-laserjet-4000-4050-4100/ Make sure they are properly clipped into place especially the tray roller. Hp Laserjet 4000 Error Codes by unknown on Aug 15, 2007 at 1:41pm Add comment Please sign in to comment 0 If you couldn't fix it with all the info on this thread and you're in Hp Laserjet 4000 Troubleshooting PrinterStopVideo 34,173 views 5:30 Review on HP Color Laser Jet Pro MFP M477fdw - Duration: 11:09.

There is a problem with the light cyan/light magenta printhead primer. check my blog I replaced the fuser and it prints when the back door is left open. Turn off the printer (see the User's guide). ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://0.0.0.10/ Connection to 0.0.0.10 failed.

Generated Thu, 20 Oct 2016 03:37:56 GMT by s_wx1196 (squid/3.5.20) saclarkdoc posted Jul 16, 2016 ARM7 LPC2138 Thiago Brandão posted Jul 5, 2016 PCI9080 DEHGHAN posted Jul 4, 2016 Firmware update's X2200 M2 ylm1994 posted May 1, 2016 Manual for ZT8817 This content is provided “AS IS” and is subject to change or removal at any time. this content So be skeptical of sticky solenoids, etc, it is usually the rollers, or the clutch if it binds up and doesn't provide some slippage. (See the service manual if you don't

That implies that you do your own research before you post a problem for the 53rd time. by unknown on Dec 11, 2007 at 1:21am Add comment Please sign in to comment 0 Thank you so much for this post - it totally was the problem and saved Thanks for the info.

The 41.5 error basically is that the paper is not hitting the sensors when expected.

Sign in Share More Report Need to report the video? by Anonymous on Feb 8, 2007 at 7:46am Add comment Please sign in to comment 0 Where is the clutch located on the HP laserjet 4000? by moe on Jul 3, 2014 at 11:20am Add comment Please sign in to comment 0 I have a laserjet 4000tn. You can print without Maintain the 49.

PCHOUSE INFORMÁTICA 22,870 views 27:41 HP LaserJet 2420 Printer Overview - Duration: 5:30. I opened it up and got the gunk out of the solenoid flap and it is now working very well. To print the manual completely, please, download it. have a peek at these guys But a lot of new people don't seem to use the Search function at all.

Possible substrate jam. The help docs I got from HP was leading me to believe I was going to have to replace the engine controller board and/or the laser scanner. If the error occurs with all substrates, call your service representative. Troubleshoot a problem Help Other Knowledge Base options Search HP Support Center Most viewed solutions Advisories, bulletins & notices Manuals Setup & install Learn & use Perform maintenance Upgrade & migrate

Someone please close it! but for now.. I will have to take a look at this clutch next time I am at work to see what its about.. What happens is when power is applied to the selenoid when a paper request is made it causes the "L" arm to move to the selenoid center and releases the gear

Turned out my duplexing option was enabled in the printer driver properties. Sticky solenoid. Huadong Feng 28,046 views 11:09 Time lapse printer service - Duration: 8:27. Warranty status only indicates current warranty state.

by Anonymous on Apr 28, 2010 at 8:53am Add comment Please sign in to comment 0 THANK YOU! Change product Choose from all HP products Enter product serial number Please wait while we process your request. These are the ends of the pick rollers.If these are worn then this can be your problem, I just fixed one this way that two other techs had literally replaced all I will try to replace the feed assy behind tray 1.