Home > Hp Laserjet > Laserjet 4300 Error Codes

Laserjet 4300 Error Codes

Contents

Press the Check button one more time to Print Menu Map and then press the Check button. DISK FILESYSTEM IS FULLalternates withReadyFor menus press "CheckMark Icon" 13.13.00JAM INSIDE DUPLEXER DISK ISWRITE PROTECTEDalternates withReadyFor menus press "CheckMark Icon" 13.1C.00FUSER JAM EIO X DISKNOT FUNCTIONALFor help press 13.20.00 JAM IN It causes static electricity, which can, in turn, cause paper jams. Press the (Up Arrow) and (Down Arrow) buttons to step through the instructions and/or refer to the following steps. check over here

You could try to stick a stiff folder up the feed channel to see if you can free what is there. An attempt might have been made to transfer too many macros, soft fonts, or complex graphics. Caution needs to be used when installing the new assembly - be careful of the sensor flag spring! 5Si - Can be caused by field replaceable units (FRU's) not installed correctly. top 50.X FUSER ERROR For help press ? More about the author

Hp Laserjet 4250 Error Codes

Generally you will need to replace the laser scanner and ocassionaly the DC controller PCA Back back to top How did we do? Check the connectors on the DC controller and power supply. The OFF setting causes the messages to remain on the printer control panel display, and the printer to remain offline until (Select) is pressed, if an error occurs that prevents printing. Configure is properly.

Figure 32: Inserting the duplexer Open and close the top cover to clear the jam message. Look for smooth or cracked worn surfaces. If the incorrect fuser goes in, you can get a 50.5 error (or a 13.20 error in some cases) when you power on the printer. Hp Laserjet 4250n 49.4c02 Service Error Whenever the printer is ready, not busy, and has no pending warning messages, the status message “Ready” is displayed if the printer is online.

Pull it out. Hp Laserjet 4200 Error Codes There may be a problem with connection between the memory chip and DC controller. Easily replaced after removing the top cover and three wiring harness connectors. http://printerrepairsupport.com/59-4-toner-motor-error-4250-4300-4350/ top 13.06 and 13.12 JAM INSIDE REAR DOOR Description Paper jam inside or outside the rear door of the printer.

Figure 37: Removing the rear output bin Firmly grasp each side of the fuser. 13.98 Paper Jam Access deniedMENUS LOCKED 13.01.00. The line voltage and current source at the printer location might need to be inspected to ensure that it meets the printer’s electrical specifications. top top 13.01, 13.03 JAM IN TRAY (X) Description Paper jam in one of the trays/open and close top cover.

Hp Laserjet 4200 Error Codes

Figure 45: Disconnecting cables Grasp the cover on the right side of the printer and pull it firmly toward the rear of the printer until it stops. https://www.orionmarket.com/product_error_page/HP/HP-4300/ Action If the incorrect size was selected, cancel the job or press the Help (?) button to gain access to help. Hp Laserjet 4250 Error Codes Use (Up Arrow) or (Down Arrow) to scroll to PRINT CONFIGURATION, and then press (Select). Hp Laserjet 4200 Cartridge Installed Message To reach the settings, open the Configure Device menu at the printer control panel.

Thank you and your firm again, you were terrific. check my blog Action Contact HP or an authorized service provider. The ON setting determines that the clearable warning message appears until (Select) is pressed. If the error message persists, contact HP support. Hp Laserjet 4200 And 4300 Series Printers Drivers

alternates with 59.XY PRINTER ERROR To continue turn off then on Description A temporary printing error occurred. Defective Formatter PCA - Replace with known operational board and try again. Replace device which triggers error. this content If paper is difficult to remove, try clearing it from the tray area.

Preheat oven to 350 degrees F. Hp Laserjet Error Codes Figure 41: Installing rear-output bin Plug the power cord into the printer. HP Color LaserJet printer service error code repairs in Los Angeles and Orange County!

How did we do?

Remove any accessories (font cartridges, memory PCA's, SIMMs, etc.) plugged into the formatter card and try again. On the barcode you will find an HP part #, check the part# on your fuser to see if it matches in the list below.   If the fuser part# does not Is the paper size correct? 82.0180 Eio 2 Error Action Turn the printer power off and then turn the printer power on.

Figure 1: Opening top cover and removing print cartridge Use the green handle to lift the paper-access plate. Flex the arms on the plastic output bin slightly to remove one side of the tray at a time. AUTO CONTINUE has two settings, OFF and ON (the default). have a peek at these guys Also, can I get some instructions on putting in the rollers.

For best results, use the HP driver that came with the printer. (See the printer user guide for information about printer drivers.) Press (Select) to clear the error message. (The job Figure 43: Reinstalling duplexer Turn the printer power on. If the software tells the printer to expect a different size (legal, A4, COM10) than the tray available, you will get an error. Grasp both sides of the paper, and slowly pull the paper out of the printer. (There might be loose toner on the paper.

If the problem persists, contact HP Customer Support. Check the HP paper specification guide for more info. Print a menu map by pressing the Check button and then the Down Arrow to Information. On the LJ4/4M/4+/4M+ the sensor flag can get knocked out of place when a paper jam occurs and the tray is pulled out abruptly.