Home > Hp Laserjet > Lj 4300 Error Codes

Lj 4300 Error Codes

Contents

Serious? There are a lot of third party rollers for this machine that are either oversized or the rubber wears out sooner than the OEM’s so look for rubber debris below or Replace the DC controller. 52.X PRINTER ERROR The laser scanner speed is incorrect. On older style printers this is often caused by a bad main motor. (Older style printer being printers with halogen heating elements in the fuser - 4, 4+, 5, 4si, 5si, get redirected here

Replace the formatter and/or firmware DIMM. 4. Note:It is not necessary to remove the Fuser Assembly or the Toner Cartridge. You can even send us your printer for repair. by Anonymous on Jun 19, 2007 at 11:41am Add comment Please sign in to comment 0 1.

Hp Laserjet 4250 Error Codes

Push up on that plate. Privacy Policy Terms of Use On Sale About Us Contact Us Order Status FREE TECH SUPPORT (877) 755-5300 Login My Cart (0) Printers Printer Supplies Printer Parts Printer Accessories Error Codes Try replacing the fuser.) 56.X PRINTER ERROR An incompatible combination of input/ output bins was selected.

Install the replacement fuser by inserting it and aligning the left side first. See Tray 2 feed rollers (this procedure includes the separation roller). 5 Replace the dc controller PCA. Just finished testing the baked card, and it works perfectly.Moe, many thanks! Hp Laserjet 4250n 49.4c02 Service Error You said the "Down arrow." Unfortunatly, that did not help either.

If the incorrect fuser is installed, you can get a 13.20.00 error (or a 50.5 error in some cases) when you power on the printer. Hp Laserjet 4200 Error Codes If it is not within the proper range, replace the fuser. Remove and reinstall the paper to make sure it is installed properly and that it’s not folded over in front of the tray. http://printerrepairsupport.com/59-4-toner-motor-error-4250-4300-4350/ Pull it out.

The display should show skip disk load. 13.98 Paper Jam Step 6.) Remove Formatter Assembly. Try the DIMM in another slot. (The firmware DIMM must remain in slot #4—the lowest DIMM slot.) 3. All rights reserved.

Hp Laserjet 4200 Error Codes

Press select. https://www.orionmarket.com/product_error_page/HP/HP-4300/ Remove any installed accessories (example stapler/stacker). Hp Laserjet 4250 Error Codes eCommerce Solution : k-eCommerce Do-It-Yourself Printer Repair Search Primary Menu Skip to content AboutContactHOMELinks Search for: Error Codes, Hewlett Packard Laser Jet 4200, Hewlett Packard Laser Jet P3005 series printer, Hewlett Hp Laserjet 4200 Cartridge Installed Message If you don't know how to remove the fuser from your printer,it's not difficult -- see the removal instructions farther down the page.

One of the labels came off the backing sheet inside the printer. http://softacoustik.com/hp-laserjet/lj-2200-error-codes.php Repeat this selection procedure until the entire eight (8) digit Pin Code is saved.8. Step 2.) Paper Tray 2 Step 3.) Remove Tray 2 extension door /Paper Tray Dust Cover. The page containing the error will automatically be reprinted. 1. Hp Laserjet 4200 And 4300 Series Printers Drivers

ERROR The requested URL could not be retrieved The following error was encountered while trying to retrieve the URL: http://h20564.www2.hp.com/hpsc/doc/public/display?docId=emr_na-bpl12422 Read Error The system returned: (104) Connection reset by peer An Paper pickup roller - Gray spongy rubber roller on a white cylinder and 24-tooth white gear on one side MFG Part Number: RM1-0036-000CN Condition:Refurbished MFG:HP This HP RM1-0036-000CN Replace the engine controller board. 5. useful reference Access deniedMENUS LOCKED 13.01.00.

by tcosmas on Nov 5, 2008 at 11:42am Add comment Please sign in to comment 0 I printed a sheet of labels. Hp Laserjet Error Codes Take the plastic front off, it's held by 2 torx screws. Check the main motor’s cable to ensure that it is seated properly. 4.

Step 1.) Begin by removing all Optional Equipment.

Remove 2 screws or 2 thumb screws and grasp the formatter cage and then slide it away from the machine to remove it. by dmzcompute on Nov 16, 2007 at 4:44pm Add comment Please sign in to comment 0 Had a 4250 with 68.2 permanent storage error on LCD upon bootup. Plug the printer into a wall outlet and see if this resolves the problem. 3. 82.0180 Eio 2 Error The folder may free it but most times you have to remove the tray 1 assembly to get to it and put it back in the right position.

You’re done! NOTE: When reinstalling the cover make sure that the power switch connecting Rod goes in between the on/off switch Lever guide inside the cover. If it was stuck in the down position, the printer would think a piece of paper was holding it down. this page X description: 0 = Motor error 1 = Motor startup error 2 = Motor rotation error 1.

The best way to determine which fuser you have is to pull the fuser out of your printer and check the barcode label on the fuser. Replace the environmental thermistor. 4. Reseat cables to the laser/ scanner and engine controller. 4. If a duplexer is installed, remove it from the back of the printer.

All Rights Reserved. DISK FILESYSTEM IS FULLalternates withReadyFor menus press "CheckMark Icon" 13.13.00JAM INSIDE DUPLEXER DISK ISWRITE PROTECTEDalternates withReadyFor menus press "CheckMark Icon" 13.1C.00FUSER JAM EIO X DISKNOT FUNCTIONALFor help press 13.20.00 JAM IN and may not be used without advance written permission of PrinterTechs.com, Inc. Put everything back in reverse order.