Home > Kenmore Elite > Kenmore Elite He3t Error Codes Fh

Kenmore Elite He3t Error Codes Fh

Contents

Top-Load Washer - White See Details Kenmore 23102 3.6 cu. So I pulled the drain pipe from a narrow metal drain and the washer works now. Plug in washer or reconnect power. This occurs when there is no air gap for the drain line at the standpipe. Check This Out

http://www.fixya.com/support/r385844-checking_drain_pump_kenmore_elite_front If the above procedures do not correct the problem, it is recommended by the manufacturer to replace the drain pump.Take care May 31, 2010 | Whirlpool Duet 3.8 cu. All rights reserved. © Applianceblog.com 2004 - 2014 iFixit: Repair Manual Official App Free – Google Play Install Select a Language: 中文 日本語 Deutsch English Español Français Italiano Nederlands Português Русский Check/Repair: Press PAUSE/CANCEL twice to clear the display. Broit 181.841 προβολές 9:37 Kenmore HE5t Washer Repair for Error Code F21 & Sud - Διάρκεια: 5:02.

Kenmore Elite He4t Washer Fh Error Code

Silicone would be more flexible and stretch over the fittings easier. Verify Drain pump operation 2. At this point (if no pauses are detected), the tubing connected to the pressure switch should be checked for air leaks, disconnection or obstructions. Front-Load Washer See Details Kenmore 20222 3.3 cu.

Now we have to wait several days to get the parts and then have repairman come back out to install. I guess we will need to use a laundry bag to wash little baby things. Oops! Kenmore Elite He3t Washer Error Codes error code flashes h and then f.

No success. Kenmore Elite He4t Washer Error Codes I see & hear the water coming in… Was this answer helpful? Get more answers from the people in your networks Tags Kenmore , Washers Click to remove this tagging. Smaller machines than ours can use slightly lessor amounts of the detergent.

Repair Help > Washer Repair » whirlpool duet error code FH .... Kenmore Elite Quiet Pak 2 Error Code Fh Check the drain pump for foreign objects and debris. Undo rhollin Does anyone know what the F2 error for the Kenmore HE4t means? Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3.

Kenmore Elite He4t Washer Error Codes

FH code during wash cycle and running diagnostics step 4? (wash) - with high water levels and resetting the control panel to drain/spin (no spin) to get the water out. My machine was just purchased used, and had some ice issues, (despite the seller's assurance it was properly drained) I'm thinking it is likely the flow switch is bad, but could Kenmore Elite He4t Washer Fh Error Code Add a Youtube Video: Paste a YouTube URL in the text field above.

Please enter a YouTube URL Search YouTube:

Please search for a video × What's Wrong? Kenmore He3t Washer Diagnostic Mode How do I test the flow meter and pressure switch???

Can anyone tell me where the pressure valve is located? his comment is here Check the following:- Make sure you don't have a siphoning problem. Inspect the small black tubing for a worn spot &/or hole. Browse Categories Answer Questions Kenmore Elite 45986 Front Load Washer Kenmore Elite Washing Machine Kenmore Washing Machine Washing Machines All Unanswered Join Sign In Ask a Question × HomeForumWashing MachinesKenmore EliteElite Kenmore Elite He3 Pressure Switch

I have been getting the HF error message for several days in a row. I can push "Pause" and then "Start" and the machine will resume operation. I ran the diagnostics and the C00, C01, C02 and when it went to C03 the FH error code came back on Expert: Brian replied7 years ago. this contact form ft.

tanksalotct 180.267 προβολές 6:03 Using a Schematic to Troubleshoot a Whirlpool Front Loading Direct Drive Washer that Won't Run - Διάρκεια: 15:25. Hf Code On Whirlpool Duet Washer I have good water flow, good drainage. If the error code returns, proceed to step 2.

Make sure you don't have any duct tape or something around your drain pipe, it needs that air gap to prevent siphoning.

If not, click on the following link to check the pump for obstructions: http://www.fixya.com/support/r385845-checking_drain_pump_in_whirlpool_duet To access the Flowmeter and Pressure Switch – remove the three screws in the top panel along Again Thanks HBW258 For taking time out of your busy schedule to help a total stranger as myself you should and probably do feel good about yourself. When blowing air back into drum there seemed to be some resistance in airflow, is this normal?. Kenmore Elite Flow Meter If after 30 seconds the control does not detect water entering machine and then valves will be turned off and the error code will be displayed.

Again, this is an intermittent problem and sometimes a cycle will run perfectly without error code or stoppage. OR If the control has turned the water valves on and after 8 minutes the flow sensor has detected 10.5 gallons of water passing through it, but has not detected the If it sticks, tap either side and it should come free. http://softacoustik.com/kenmore-elite/kenmore-elite-he3t-error-codes-sud.php Check for plugged or kinked inlet hoses or plugged screens in the inlet valves 3.

It doesn't always get you to the solution but it does get you in the neighborhood - then check it all related paths before buying parts. Undo AZHeidi Where is the flow meter, the pressure switch...and, what is the CCU? Undo dooozie I have the exact same problem. Check/Repair: Press PAUSE/CANCEL twice to clear the display.

Your question was published, help is on its way! I have hot water and I have cold water as long as its on wash cycle. Just keeping you guys up to date . Get more answers from the people in your networks Tags Kenmore , Washers Click to remove this tagging.

There will be some resistence when blowing through the pressure switch hose. Make sure that both valves at the water source(s) are turned on all the way. 2. To check the drain pump, click on the following link for step-by-step instructions. I timed the occurance: 10 1/2 minutes after I push start the error happens.

This problem occurred on an 8 year old Kenmore Elite Washer. After operating the washer a few minutes to completely dissolve the detergent, pause the washer, open the door and swab down the complete bellows assembly including the hidden folds and adjoining The pressure switch is located on the right-hand side of the washer in the rear. Share it!

On Sale Now 1 Answer Filter by: Most Helpful Newest Oldest Chosen Solution mayer @mayer Rep: 424.9k MacHale Enterprises 735 469 1.4k Posted: 02/21/2012 Options Permalink History F/H: Condition No water Check the pump impeller and make sure there's nothing caught in it. Do you notice an above normal amount of water in the washer when you notice the error code? I have to push the drain/spin button.

I have made no changes in personal water use and have no city water pressure issues.