Home > Kenmore Elite > Kenmore Elite He4t F2 Error Code

Kenmore Elite He4t F2 Error Code

Contents

ReplyWas this helpful?Helpful? Thanks tech17, you will always be relevant! I used an "EZ Mover Furniture Lifter" to tilt the washer and put two pieces of wood under the sides near the front. (Female, in my 60's, so not super-strong.) Per Also called Sears to cancel their home visit for tomorrow. Check This Out

It is kinda wierd how the impeller turns. We haven't used them in years! So if it works part of the time, but not all the time, what do I need to do to fix it? You must remove the front panel of front-load models to access the drain pump or lay top-load models on the ground to access the pump beneath the washtub.

Kenmore Elite He3 Washer Error Codes

All-Star: An expert that got 10 achievements. That's and you need to be 100% sure there are no obstructions and that the pump motor is not only working, but working at full speed. I checked the state of the Pressure Switch’s Empty and Level 1 contacts which intermittently reported the correct water level condition (EMPTY and Level 1). Your question was published, help is on its way!

You can't post conmments that contain an email address. × Comment Anonymously Video Images Dodgeru Level 1: An expert who has achieved level 1. it still keeps flashing. Once the drain/spin cycle completed, I dared to remove the trap completely. Kenmore Elite He3t Drain Pump If you suspect that the drain pump is clogged, then you can use the procedure in the following link of a previous answer to access and clear the drain pump: How

Laden... Kenmore Elite He3 F02 Error Code What's New? If the error comes back, it may require you to clean the drain pump filter again. In all cases contacts 11 and 14 (SUDS) were continuously made (connected) irrespective of water level, rinse conditions and the use of no detergent.I removed the pressure switch and tested it

I found a lot of material clogging it up. Kenmore Elite He3 Washer Parts Your question was published, help is on its way! RONDA PERRY Mar 19, 2009 I'M GETTING A ERROR CODE OF F02 AND SUD WHAT DOES THIS MEANS I'M GETTING A ERROR CODE OF F02 AND SUD WHAT DOES THIS MEANS I have been noticing that the wash cycle was taking an incredible amount of time to complete recently.

Kenmore Elite He3 F02 Error Code

The drum spins freely if I turn it by hand. Reply With Quote Page 1 of 2 12 Last Jump to page: Quick Navigation Sears Kenmore Top Site Areas Settings Private Messages Subscriptions Who's Online Search Forums Forums Home Forums Announcements Kenmore Elite He3 Washer Error Codes ft. Kenmore Elite He3 Washer Troubleshooting I had a shop vac so that definitely helped with the draining process.

Is there anything else I can try to get the washer running again? his comment is here ft. Here is a link for the website: Sears Home Services . I hope this is helpful. ft. Kenmore Elite He3 Washer Manual

Open the door and manually drain the water out of the washer with a wet/dry shop vacuum. iFixit: Repair Manual Official App Free – Google Play Install Select a Language: 中文 日本語 Deutsch English Español Français Italiano Nederlands Português Русский язык Türkçe Machine translation Help Translate iFixit Close Vice President: An expert whose answer got voted for 100 times. http://softacoustik.com/kenmore-elite/kenmore-elite-he4t-washer-error-code-f02.php In this case, the drain pump will require replacement.

Contributor 1 Answer Re: HE4t Elite F02 error code The Tech 17 solution below still works!!! Kenmore Elite He3 Washer Error Codes Fh A drain hose inserted more than 4 1/2 inches into a floor or wall standpipe drain system can cause the water to siphon back into the washtub. it use to drain it after reseting it 3 times now it won't.

Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit.

Contributor 1 Answer Re: HE4t Elite F02 error code I pulled my discharge pump and found a broken impeller shaft. I snaked the drain, cleaned the hose and put vinegar in the machine to clean it. Any suggestions? 05/14/2015 by houndhollow I just started to get this code recently and when I first called for Sears Service they said it would be $150 service call plus parts F02 Error Code Whirlpool Washer I recommend replacing the drain pump. You did not give me the model number so I am unable to give you the part number.

Yes No Cancel Update (+2 points) 5 more comments Anonymous Jul 01, 2008 where is the drain pump filter? Electrical connections run from the control panel to the side of the pump to power it. Loose Pump Connections A pump connects to the bottom of the Kenmore washtub and to the drain hose to pump the water from the washtub and out the drain. http://softacoustik.com/kenmore-elite/kenmore-elite-he4t-error-codes.php What a simple fix to a big problem.

You can see it with your light. I used a plug bar to switch it on, after I made the risky connection. The round switch is approximately 3 inches in diameter with a clear or black plastic tube connected to the bottom or side of the switch. Otherwise you'll need something like small locking vice grips (what I used).

Log in om je mening te geven. Cleaned the filter and worked 2 times. Facebook Pinterest YouTube Contests! Mayor: An expert whose answer got voted for 2 times.

ReplyWas this helpful?Helpful? It took forever. I've had the washer for over 10 years and never had a problem with it. Check Drain pump motor - OK, as water drains at a rapid rate4.

That is the motor connected to the right of the trap you just examined. See Details Kenmore 41912 2.4 cu. Good technique. You may need to manually unlock the washer door and then pull the large item filter on the pump to check for a clog.

Contributor 1 Answer Re: HE4t Elite F02 error code TECH 17 thanks for the info, problem solved . Daniel Nov 26, 2010 | Kenmore Washing Machines 1 Answer It quits on the drain cycle and a error code f02 appears Error F02 code means Long Drain If the drain MVP: An expert that got 5 achievements. It will work and drain quickly and spin and all when nothing is in it, but put anything items at all in there and it will not work.

Was this answer helpful?