Home > Kenmore Elite > Kenmore Elite Oasis F40 Error Code

Kenmore Elite Oasis F40 Error Code

Contents

I can hear a "click" in the circuit board as the error code comes up. I measured all thermisters and everything was in range. Since you have a volt/ohm meter and are comfortable using it then there are a couple of things you can check yourself to try and pin this problem down. Must be a factory defect. Check This Out

loosen the three screws in the back that hold the control panel cover on the top of the machine. hope this helpful while an expert responds with additional information. Contact service they should be able to give you more information Ask Your Own Appliance Question Customer: replied6 years ago. So I replaced it with 8577274.

Kenmore Elite Dryer Error Code F

Top-Load Washer - White See Details Related Pages Kenmore 5M followers Follow Washers 1K followers Follow Dryers 676 followers Follow Sweeps Personal Shopper Gift Registry Legal & Privacy | Help | If those connections are okay, I recommend that you take a resistance reading between the blue wire that connects to P9-1 on the machine control board and the black wire that the location of that fuse is shown in the first image below. Error Code F40 on Kenmore Elite Dryer Report This by Manage My Life September 5th, 2011 My Kenmore Elite Model 110.68087701 Dryer is giving me an error code of F40.

Tip: The max point reward for answering a question is 15. 0 characters Video Photos Link Replacement Parts Add Upload Upload × × Draw a box over the problem!! Corporal: An expert that has over 10 points. I also found that lightly and repeatedly pushing the control knob in and letting it go out after starting the dryer made the relay click even more. Kenmore Oasis Dryer Thermal Fuse hello??

Problem Solver: An expert who has answered 5 questions. I also found that lightly and repeatedly pushing the control knob in and letting it go out after starting the dryer made the relay click even more. Good luck to others who have the mysterious F40 code. Share it!

Some machines will reset themselves if they are unplugged from the wall and then plugged back in. Kenmore Elite Dryer Flashing F AppliancePartsPros 382.143 προβολές 7:36 Analyze Kenmore Elite Oasis HE Washer - Διάρκεια: 14:41. The air is leaving the dryer normally with no restriction that I can tell. Once you have determined this, then you can replace the correct part.Click on image Oct 18, 2012 | Kenmore Elite Oasis ST 6807 Dryer 1 Answer Kenmore Elite Oasis Electric Dryer

Kenmore Oasis Dryer Troubleshooting

Help this question get an answer by entering the correct category or product below. I measured all thermisters and everything was in range. Kenmore Elite Dryer Error Code F I'll check the motor control once again for voltage but I highly doubt that was even the problem in the first place as I still get the F-40 error. Kenmore Elite Oasis Dryer Thermal Fuse Location Where is the control panel, on the back?

by Joseph Perez Earned 62,685 community points in Click'>Kenmore September 5th, 2011 Answered in 10 minutes Comment Give your feedback by voting on answers 0 votes I don't thing the interface his comment is here Expert: Appliance Tech Larry replied6 years ago. CT Sun 7:30 a.m. - 9:00 p.m. I also got a low side but acceptable ohm reading on the blower motor. F40 Error Code Kenmore Dryer

Discount will be automatically applied during check-out. dickbambam Jun 18, 2014 No the real problem is cheap connectors. Before doing that beating the user interface or unplugging the power would work But after I had taken the P4 plug off several times in troubleshooting the fit was even more this contact form I'm getting the F40 error so I wanted to try your fix.

Ask Anonymously Popular Questions 3 Answers Error code on a Frigidaire affinity dryer E64 Frigidaire Dryers 7 Answers My frigidaire affinity dryer displays LOC Frigidaire Affinity 5.8 Cu. Kenmore Elite Oasis Dryer Error Code F1 Examples: Try searching again: Model Number GO Can't find your model number? Still...F-40.

Your question was published, help is on its way!

I ran the diagnostic and F40 was the only code.I check the exhaust thermistor and it showed open. Get more answers from the people in your networks Tags Dryers , Kenmore , Washers Click to remove this tagging. Be sure not to bridge adjacent edge connectors with too much solder. Kenmore Elite Oasis Dryer Recall I placed it on a frying pan to check with my ohm meter and found that it did not always open around 150 degrees F.

Bill Newberry 321.696 προβολές 4:28 Kenmore Oasis Washing Machine - Διάρκεια: 4:14. We keep the filter clean and the vent pipe unclogged. I eliminated the thermal fuse as the problem. navigate here I didn't get a chance to check wires.

After a lot of troubleshooting, I found that the control knob was the problem. OK, Continue Tips for finding your unique model number Look for your model sticker, tag or plate. Unplug and re-plug all connections you can find. F40 is a error that appears between the machine control and the motor control when communication becomes lost.

I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response if that don't work try the right panel plugs. And when I constantly and lightly pushed on the control know after starting the dryer, it would continue as normal without flashing the F40 error code. IT STARTED OUT ONCE IN AWHILE NOW IT BEEPS AND THE DRYER WILL SHUT DOWN.

I'm getting the F40 error so I wanted to try your fix. Kinda scary when you think about that... Sears Holdings reserves the right to terminate or modify this offer at any time for failure to comply with its terms and/or due to any operational malfunction of the software, hardware If the thermal fuse is burned out on that unit I would just replace the thermistor.

PeritoMay 10, 2009, 10:21 AMWhat is the model number? Customer: replied4 years ago. Also, this is something that can be done by us and no repairman needs to come to the home. However, this time every time when you pressed the "start" button, the "check filter" light would come on.

I also found that lightly and repeatedly pushing the control knob in and letting it go out after starting the dryer made the relay click even more. prev next 3 Points Related Questions: 1 Answer Any recall on Kenmore elite oasis electric dryer? Get help locating it Free Service - Appliance Repair Help & Troubleshooting ApplianceJunk.com Appliance Repair Forum Welcome, Guest. Maybe I do have a bad control board.

This expensive machine uses the cheapest parts possible. I had the same F40 code.