Home > Lexmark Error > Lexmark Error 502

Lexmark Error 502

Reply John says: 2007-09-26 at 2:52 am I tried cleaning both the rail and the encoder strip and still have the 0502 error. My boss is going to be furious!!!! I am holding it in my hand. br Lamentamos o inconveniente. news

Thanks to all the people that post here.. I too have the 502 hardware error message on my lexmark 5150. by unknown on Jan 31, 2010 at 8:49am Add comment Please sign in to comment 0 I have had a Lexmark X5150. It didn't work on the other printer. this contact form

Reply Admiral Jayce says: 2006-03-30 at 4:08 am C.J. For folks still stymied, try powering up without the cartridges. Thanks so much!

why 0502 error comes why dont u rectify problem online even though we tried a lot to clean strip,rod but same message "hardware error 0502". Cleaning the metal bar seemed to fix the problem of freezing up when copying. The magenta ( red ) does not work. If you leave the printer alone for a while, it might start printing again.

This is what real troubleshooting is about. Pull each straight out using thumb and index finger on each side of each strip.4) In back casing, using a small phillips screwdriver, remove all four screws. My copier is not connected to a computer. Now when I turn the printer on, the carriage slams across to the left hand side (with an almighty bang!) and immediately gives a hardware 502 error.

Thanks you. Share this conversation Expert: Richard replied5 years ago. Reply Dianna says: 2007-08-21 at 10:50 pm Thanks for the advice. I ended up ripping the square hole on the end-open. IT ALWAYS SOMETHING GOING WRONG WITH THEM.I HAVE KNOICA MINOLTA 2400 MAGIC PRO.

So happy I didn't, thanks for this!! http://blog.forret.com/2006/02/11/lexmark-printers-with-hardware-error-0502/ Liu Kastiju 15,033 views 13:20 TUTORIAL DESARMAR LEXMARK X4550 - Duration: 2:00. Reply Raynestar says: 2007-12-24 at 5:23 pm Just wanted to say thank you very much. I went to the Dell site and got no help.

I have tried Lexmark support and they say I need a new printer. navigate to this website Leave the power cable disconnected for 30 seconds. 4. Reply Paul says: 2008-05-25 at 5:48 pm Hooray! It took all of about 30 seconds and now my x5160 model works like a charm again.

by Anonymous on Jun 9, 2008 at 11:47am Add comment Please sign in to comment did you find out how to put the decoder strip back on if so please let Uploaded on Mar 5, 2009No sé que puede ser, se atasca el carro de la impresora al encender y aparece en la pantalla de la impresora el error de hardware 502 Works like new again now. More about the author So now its totally useless.

It should now be back in slot. Went thru the routine of unplugging the unit several times to try to get it clear (they even had me turn it upside down and shake it) but to no avail. i was ready to throw my printer away!!

I've been having this problem and it is getting worse each time.

Reply Kimberli says: 2008-11-10 at 2:40 pm worked for me! The error is now gone. I have been fiddling with this problem for over 4 weeks and finally left the Lexmark site (as their instructions obviously weren't working) -- found this link and PRESTO! Help.

I can't even tell you how many resources I've wasted on this problem. I wiped and got the black residue; printer now works just fine. Reply e says: 2007-11-05 at 4:33 pm i cleaned the rod and it worked! http://softacoustik.com/lexmark-error/lexmark-error-126.php Thanks so much All…… Happy Camper Reply Jane says: 2007-02-07 at 10:52 am Great tip finally got the damn thing to work again!

Once I knew how to slip it back on, the problem was solved. I thought I was going to have to pull the whole thing apart!!! I had, however, to turn on the printer while the cover was open, in order to get the cartridges to go in the middle, so I could clean the left side The front top casing and the bottom casing SEEM fused together, but they come apart and snap back together.

I hated the thought of having to throw this thing out - you saved us! These steps were not as easy as they sound.