Home > Lexmark Error > Lexmark Error Message 0502

Lexmark Error Message 0502

A Bonus and Positive Feed Back are appreciated Freddy M. There was an error with the application. Credentials confirmed by a Fortune 500 verification firm. Still nothing. news

logojet 52.587 προβολές 2:13 DTG Kiosk cleaning the encoder strip - Διάρκεια: 3:49. I do not know where the encoder strip is on this model to make sure it is seated properly. Other faults that can bring up this error is a carriage rail that needs cleaning and oiling (so you might want to do that while your inside the thing), and also The printer should print a sheet of paper with one black bar and one grey bar. 4. http://support.lexmark.com/index?productCode=LEXMARK_X5150&segment=SUPPORT&page=content&id=HO2707

RPI Solutions is online now I have a Lexmark All-In-One X6170 printer that has an error Resolved Question: I have a Lexmark All-In-One X6170 printer that has an error "0502". Switch off the printer using the power button. 2. Lightly press the strip first to the rear and then forward, if necessary. 9. I followed the instructions you posted, and it's working perfectly again now.Thanks again,Craig.

If the encoder strip was re-seated correctly, the Hardware Error: 502 code will not appear. with picture included: Re-position the Encoder Strip on your Printer To re-position the encoder strip, perform the following steps: 1. Went thru the routine of unplugging the unit several times to try to get it clear (they even had me turn it upside down and shake it) but to no avail. by unknown on Apr 5, 2011 at 9:08pm Add comment Please sign in to comment 0 my file is open contune by unknown on Jun 11, 2011 at 5:14pm Add comment

Seems I got the error message after installing a new (genuine) 82 cartridge. It comes off like this: Don't break anything. Disconnect the power cable from the back of the Lexmark X5100 / X6100 Series. 3. Can anyone peek back there and tell me where it was connected and any other information to help me get it back in?

Thanks. fastprintersdotcom 18.710 προβολές 9:41 Φόρτωση περισσότερων προτάσεων… Εμφάνιση περισσότερων Φόρτωση... Σε λειτουργία... Γλώσσα: Ελληνικά Τοποθεσία περιεχομένου: Ελλάδα Λειτουργία περιορισμένης πρόσβασης: Ανενεργή Ιστορικό Βοήθεια Φόρτωση... Φόρτωση... Φόρτωση... Σχετικά με Τύπος Πνευματικά δικαιώματα Using an index finger, gently push encoder strip down and then back up to get it back into the slot located on the back of the ink cartridge carrier. Your Own Question Freddy M., Technician Category: Printers Satisfied Customers: 18398 Experience: Years of IT and customer support experience 15852642 Type Your Printers Question Here...

ONE HAS A SENSOR IN IT WITH A LONG WIRE THAT COILS INTO A SPRING. TUTORIALES-MASTER 619.023 προβολές 6:05 CARA PÁLIDA PARA MINISTROS EN HOMENAJE FUNADO A JAIME GUZMAN. - Διάρκεια: 0:45. Some dark dirt transfered onto the cloth. If the printer fails to print, remove both cartridges and try the test again. (It will feed the paper through and print a blank page.) 5.

Use a soft cloth, like facial tissues without lotion on it.I cleaned the strip with a soft clean cloth. http://softacoustik.com/lexmark-error/lexmark-error-126.php They helped. Slide the cartridge carrier to the middle of the printer by taking the top part of the belt and moving it gently to the right. 5. I poured in 91\% rubbing alcohol and let it drip into a sink in that direction careful not to get any alcohol on electrical components or the encoder strip.

Move the cartridge to the extreme left and wip the firm strip.This has help me correct my problem with a couple of x6170's.Good Luck. Leave the power cable disconnected for 30 seconds. 4. I went to Lexmark.com and found a fix for it. More about the author After about 2 hours of work.

by unknown on Mar 30, 2009 at 2:01am Add comment Please sign in to comment 0 Hi, help needed here,I have a X6150 multifunction printer, after fixing the gear roller the I had to persuade them to tell me. Any aftermarket parts?

Make a standalone copy. 13.

by unknown on May 5, 2010 at 9:55pm Add comment Please sign in to comment 0 Thanks, [emailprotected] Worked for me on a Lexmark X6170, though the options menu is a Press the Option button 10 times until Cartridges appears on the LED display. 2. I have talked to support (overseas) and they were unable to help. If the copy is satisfactory, repeat the test once to confirm that the error is gone.

press check to print alignment page. http://blog.forret.com/2006/02/lexmark-printers-with-hardware-error-0502/ Thanks, Robert Preston Ask Your Own Computer Question Customer: replied7 years ago. When I try to test print a page a message says there is a print job in progress but when I open the printing queue there are no jobs pending. click site I love this old dog printer-had it over 5 years now and just wanted to keep it going, as money is tight.

This is where it's tricky because it seemed as if the factory lightly melted a few joints just so you'd break it if you tried to take it apart. Easiest fix ever!Now I tried it on my old printer and the magenta does not work. Login|Contact Us Computer For Online Computer Support, Ask a Computer Technician Not a Computer Question? This occurs when attempting all operations, Maintenance, cleansing, copying etc...

Press the + button 4 times until Self test appears on the LED Display. 3. Thanks - unknown 0 Does anyone know where I can get the Encoder strip. Now if only I could get paid for it.I STILL don't understand how simply wiping a plastic ribbon with a clean cloth fixes electronics, but it worked one time on one C'è stato un errore con l'applicazione.

I accidentally knocked this out and had to find a hole where it goes back in. I called Lexmark technical support and was able to finagle a few answers out of one guy for free: he said to NOT use alcohol or other chemicals on the encoder Alonso 8.931 προβολές 0:45 COMO INSTALAR UN SISTEMA DE TINTA CONTINUA EN HP 4500 - Διάρκεια: 6:47. dirtmax64 8.587 προβολές 1:30 DESENSAMBLE Y ENSAMBLE DE UNA IMPRESORA LEXMARK - Διάρκεια: 4:37.

Take out both cartridges. 6.