Home > Lexmark Error > Lexmark X340 Error 88

Lexmark X340 Error 88

Contents

Dan Erim Ortiz 518 προβολές 7:00 Video Aula Recarga Toner Lexmark E230, E232, E240, E242, E330, E332, E340, E342, X340, X342 - Διάρκεια: 8:57. Check paper sensor flag for restricted movement or damage. Check the fuser lamp is the correct type of lamp that should be installed. • Verify the line voltage is not exceeding the maximum rating for the printer. Load correct size Error 28 Input sensor not made after pick attempt. http://softacoustik.com/lexmark-error/lexmark-x340-error-250.php

test). There should be zero ohms resistance between the transfer roll shaft and the high voltage supply contact. Check for 24V at red wire on interlock switch with door closed 4. Reload the paper and do a power on reset.

Lexmark Error Codes

Replace defective cartridge. What Our Users Say Press & Media Contacts Advertising DMCA Policy Brands × Login Login to ManualsLib Don't have an account? Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Unit. For more information, see Loading paper in the manual feeder on page 32.

So that you find Happy Printer RepairERROR 20 / ERROR 200 Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Partial document scans Make surethedocument isloaded correctlyintothe ADForonthescanner glass.Formoreinformation,seeScanningonpage54. To change the scanning resolution to a lower value: 1 From the control panel, press Scan. 2 From the QLINK dialog on the computer screen, select the location you want to Lexmark Dc Pick Motor Check the operation of the toner sensor.

Verify correct cable connections from the Engine board to the HVPS. Lexmark Printer Error Messages Error 82 Photo Developer Cartridge Exhausted The Photo Develper (OPC belt cartridge) has reached the end of it’s life and must be replaced. For more information, see Scanning on page 54. http://www.all-laser.com/aerrorlex/ Close all applications not in use.

Error 80 Network Card Codes These user codes are documented in various network card user manuals. Lexmark Error Codes Problem Open doors and covers and remove the toner cartridge. Make sure the memory shown on the printout matches the installed memory. Error 37 37 Insufficient Collation Memory Memory is too full to collate the print job.

Lexmark Printer Error Messages

Make sure that the paper size settings match the paper in the tray. http://www.manualslib.com/manual/92455/Lexmark-X340.html?page=88 Scanwasunsuccessful. Lexmark Error Codes If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace Service Error 146.00 Dc Pick Motor Print and copy troubleshootingpage 84................................................................................................................................................................

Make sure the MFP is connected to an analog telephone line. navigate to this website ERROR 22 The exit sensor was not unmade in time. Check fan for binding or defective bearing - Replace Fan How did we do? For supplies information, see on page 69. Lexmark Engine Error

For more information, see Scanning on page 54. Run the Quick Disk Test. Fuser errors can be from a cold fuser or an overheated fuser. More about the author Replace the Autocompensator Assy.

A secondary error indication can be obtained by pressing an releasing a button. 938.06 Service System Electronics Error 80 Network Card Codes These user codes are documented in various network card user manuals. Scans very slowly Close all applications not in use.

Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected.

Remove and reinstall print cartridge. Partial document scans Solution Check the display. RentingImpresoras 18.325 προβολές 1:46 Φόρτωση περισσότερων προτάσεων… Εμφάνιση περισσότερων Φόρτωση... Σε λειτουργία... Γλώσσα: Ελληνικά Τοποθεσία περιεχομένου: Ελλάδα Λειτουργία περιορισμένης πρόσβασης: Ανενεργή Ιστορικό Βοήθεια Φόρτωση... Φόρτωση... Φόρτωση... Σχετικά με Τύπος Πνευματικά δικαιώματα Lexmark Printer Error Lights Make sure cable connections for the following hardware are secure, if applicable: • Power supply • Telephone • Handset • Answering machine Check the telephone wall jack. 1 Plug a telephone

If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. Some 920.xx error codes may be cleared by turning the printer on and off and allowing it to complete POR. Partial document scans Make sure the document is loaded correctly into the ADF or on the scanner glass. click site Resend the fax.

If the error message still appears after restarting the computer: 1 Insert the Software and Documentation CD. 2 Install the QLINK software. or ClickStart ÆControl PanelÆPrintersandOtherHardwareÆ Printersand Faxes. 2Double–clicktheLexmark X340/X340n/X342nicon. 3ClickPrinter,andmakesurenocheckmarkappearsnextto Pause Printing. 4Makesurea checkmarkappearsnextto SetAsDefault. The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. If the test fails, the disk is defective or the data on track1 is bad.

Replace System Board Request Quote Error 917 Transfer Roll Error Cannot start servo operation. Error 47 47 Font Card Removed While Printing Printer needs data on removed card.