Home > Lexmark Printer > Laxmark Error

Laxmark Error

Contents

If cables, connectors and connections are good replace assemblies listed. Replace the disk if instructed by the operator panel. Ensure the transparent tape is removed from both cartridges. Insert a memory card with a correct or supported format.

Close all unused documents and applications. Remove the duplex front cover to access the jam area. Load more paper. Observe the lamp through the left near side of the printer. https://www.marketpoint.com/lexmark-error-codes.aspx

Lexmark Printer Error Code Ec5

Lexmark Fuser Pricing Error 925 A 925 service error indicates the wrong fuser lamp is installed in the printer and does not match the one stored in the printer code. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 924 924 Fuser Error - Open circuit detected in thermistor circuit. Make sure the memory shown on the printout matches the installed memory.

Error 38 38 Memory Full Memory used to store pages is full. Service Error Codes Other Troubleshooting Tips 200 Paper Jam T65X Troubleshooting 201 Paper Jam Power Issue with Input and Output Options Installed 80 Scheduled Maintenance The Difference Between Fuser Type 1 Request Quote 947 Engine Board Engine board failure Replace the Engine Board Request Quote 953-954 NVRAM Failure NVRAM Failure 953: NVRAM Chip Failure 954: NVRAM CRC Failure Optra T 640/642/644 Lexmark Printer Error Lights Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do?

The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. Lexmark Printer Error Messages We got it this morning and I have it installed. Error 921 Fuser is below standby temperature when idle. http://support.lexmark.com/index?page=content&id=SO4438&userlocale=EN_US&segment=SUPPORT&productCode= Error 43 Font card format not supported by printer.

Error 47 47 Font Card Removed While Printing Printer needs data on removed card. 938.06 Service System Electronics Size Warning In Photo mode, resized image is larger than the selected blank paper size. Out of memory The scanned image has taken a large amount of system memory. Check the continuity of the fuser lamp at the two heavy leads.

Lexmark Printer Error Messages

Pay close attention to the area where the toner cartridge sits. http://support.lexmark.com/index?page=content&locale=EN&productCode=&segment=SUPPORT&viewlocale=it_IT&searchid=1457159543205&actp=search&userlocale=EN_US&id=TE359 If you receive this error, you must reduce the resolution, color depth, or crop area. Lexmark Printer Error Code Ec5 Press Select to retry alignment. Photo mode A memory card is not inserted correctly or is damaged. Lexmark Engine Error System Board Pricing Request Quote 975-979 Network Card X Indicate a network card failure in the specified slot, X=any card in slot 1 or 2. 975- Unrecognizable Network Card 976- Unrecoverable

Replace the transfer roller as necessary. Cartridge missing No cartridge present in the cartridge carrier. If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. If the test fails, the disk is defective or the data on track1 is bad. Lexmark Error Codes Problem

Reconnect. Replace Printhead Pricing Error 932 Lost hsync No High voltage signal - check connections at both ends of cable for corrosion or oxidation. As you scan, pay attention to the file size display on the Scan dialog to monitor file size. Replace the Autocompensator Assy.

Check the wiring harness cable. Lexmark Ms310dn Error Codes Open the printer rear door to access the jam. Verify latch relay is operating - slowly close door and listen for interlock switch 3.

The main motor is located just to the left of the toner cartridge.

Thank you and your firm again, you were terrific. Fuser Pricing How did we do? Press Select. Lexmark Crc Failed Do Not Power Off Check Toner Sensor Check Cable Check System Board Check developer drive for worn, loose or broken parts.

We can email further info if needed for your particular model. The product was delivered just a few minutes ago. My Account| Cart| Order Status Market Point Search: select Advanced search Read Customer Reviews GSA Contract Schedule Enter Here Need Assistance? Close all unused documents and applications.

Replace the bump alignment motor Replace bump motor Replace interlock switch Replace System Card Error 230 Paper Jam - Check Duplex The paper is most likely jammed in the Duplex Make sure top access door is closed securely 2. Newer machines display a sub code to indicate which condition applies. Error 7X Network Card Codes These user codes are documented in various network card user manuals.

Ensure the card is inserted correctly and is not damaged. File is too large You have exceeded the amount of data a scan file can hold. Error 80 Network Card Codes These user codes are documented in various network card user manuals. Delete old scans or files that you no longer need to free up disk space.

The main motor assembly may need to be replaced. Reconnect. Remove jammed media How did we do? Try opening Tray X.

Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on Replace the assys in the following order 1. Error message or title What it indicates Solution Ink low The print cartridge is running out of ink. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact.

If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed. Install more memory Simplify print job Delete fonts, macros and other data stored in RAM Error 39 Page too complex to print.To verify that the printer recognizes all the installed memory,