Home > Lexmark Printer > Lemark Error

Lemark Error

Contents

For more information, see Loading paper. Ensure the transparent tape is removed from both cartridges. eCommerce Solution : k-eCommerce 3567 Benton Street, Suite 243 Santa Clara, CA 95051 800.360.1337 408.745.9800 Order Desk: 8 AM to 5 PM Home Contact Us About Us Terms of Sale Feedback If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service.

Press Select to load the paper and continue printing. Check the wiring harness cable. Check paper sensor flag for restricted movement or damage. Remove the duplex front cover to access the jam area. https://www.marketpoint.com/lexmark-error-codes.aspx

Lexmark Printer Error Code Ec5

Pay close attention to the area where the toner cartridge sits. Replacement of the thermistor is not a cost effective repair, replace fuser assembly. If you have other tech support questions that are not covered here, send email to [email protected]

Check fan connector and cable for loose or damaged connection. Note: This error indicates the printer was able to read the cartridge ID, but the ID did not pass the verification test. It may take the printer 10-20 seconds to determine if the print cartridge is defective. Lexmark Printer Error Lights Replace low voltage power supply assembly.

Request Quote Error 920 920 Fuser Error indicates the Fuser is below temperature while printing. Lexmark Printer Error Messages Error 920.X and 922.XX may display for a cold fuser. Check the operation of the toner sensor. Blank paper size selected is too small for one of image already selected.

May be due to the paper feeding manually while motors running and previous page in path. 938.06 Service System Electronics Los Altos Hills, CA Thank you. Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. System Board Pricing Request Quote 975-979 Network Card X Indicate a network card failure in the specified slot, X=any card in slot 1 or 2. 975- Unrecognizable Network Card 976- Unrecoverable

Lexmark Printer Error Messages

Service Error Codes Other Troubleshooting Tips 200 Paper Jam T65X Troubleshooting 201 Paper Jam Power Issue with Input and Output Options Installed 80 Scheduled Maintenance The Difference Between Fuser Type 1 email with model, primary and secondary pattern for troubleshooting info. Lexmark Printer Error Code Ec5 Newer machines display a sub code to indicate which condition applies. Lexmark Engine Error Insert print cartridges in the correct carrier.

Replace System Board Request Quote Error 917 Check the transfer roller for toner buildup, surface damage to the roller, oil, or other contaminants on the surface of the roller. May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner. A secondary error indication can be obtained by pressing an releasing a button. Any help here would be appreciated too. Lexmark Error Codes Problem

A second memory card is inserted. See “Network Wrap Tests” on page 23. Check the toner metering cam on back of suspect cartridge. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers

Press Select to select a new blank paper size, or press Stop/Clear to cancel the current DPOF print job. Lexmark Ms310dn Error Codes Clear the carrier jam. As you scan, pay attention to the file size display on the Scan dialog to monitor file size.

Error 928 Erase lamp assembly missing or disconnected Error 929 The toner sensor is not operating properly, the developer drive assembly is not operating properly or the print cartridge is

In general, fuser errors require replacement of the fuser as a cost effective repair. Can be system board or printhead. File is too large You have exceeded the amount of data a scan file can hold. Lexmark Crc Failed Do Not Power Off Observe the lamp through the left near side of the printer.

Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it Paper not being picked up check paper tray & pickup rollers Replace rollers if worn smooth or cracked ERROR 21 The exit sensor was not made in time after the input Also, can I get some instructions on putting in the rollers. Replace fuser assembly Replace Fuser Lexmark Fuser Error 145.XX (C520X/530X) Motor bump aligner service check 1.

Insert a memory card with a correct or supported format. Additional info on X and XX codes available by email.