Home > Lexmark Printer > Lexmark Error

Lexmark Error

Contents

Perform fuser service check. Newer machines display a sub code to indicate which condition applies. If you have other tech support questions that are not covered here, send email to [email protected] System Board Pricing Request Quote 975-979 Network Card X Indicate a network card failure in the specified slot, X=any card in slot 1 or 2. 975- Unrecognizable Network Card 976- Unrecoverable news

For more information, see Jams and misfeeds. Paper out The All-In-One is out of paper. Replace the transfer roller as necessary. Error 37 37 Insufficient Collation Memory Memory is too full to collate the print job. Replace Printhead Pricing Error 935 Printhead Error - May have sub-codes. https://www.marketpoint.com/lexmark-error-codes.aspx

Lexmark Printer Error Code Ec5

If you are installing a black or photo cartridge, insert it in the left carrier. Close all unused documents and applications. Also, if the accumulated sheets are removed, the portion of the job printed after the jam will not be stapled.

The thermistor provides feedback on the temperature of the fuser roller and when it fails, the fuser power is shut off and the fuser does not heat up. Check the toner metering cam on back of suspect cartridge. Error 24X Paper Jam - Check Tray "X" Primary: Paper is jammed around Tray X (X=tray 1 thru 5). Lexmark Printer Error Lights Size Warning In Photo mode, resized image is larger than the selected blank paper size.

Press Select to select a new blank paper size, or press Stop/Clear to cancel the current DPOF print job. Lexmark Printer Error Messages Send an Email Toll Free: 877-365-1903 About us Terms Contact us Help Login Brand : All brands HP Models Lexmark Models Xerox Models Model : Choose a brand All rights reserved. http://support.lexmark.com/index?page=content&id=SO4438&userlocale=EN_US&segment=SUPPORT&productCode= Error 31 Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected.

Veronica Casto Houston, TX It is nice to place anonline order & get to talk to an actual person. 938.06 Service System Electronics Reconnect. The fuser can usually be removed with two simple screws and the entire assembly lifted out. Check connections to the to interconnect card assembly.

Lexmark Printer Error Messages

If you are installing a color cartridge, insert it in the right carrier.For more information, see Installing the print cartridges. Alignment Error The transparent tape is still on the cartridge nozzles. http://support.lexmark.com/index?page=content&locale=EN&productCode=&segment=SUPPORT&viewlocale=it_IT&searchid=1457159543205&actp=search&userlocale=EN_US&id=TE359 The transfer roller is included in the maintenance kit. Lexmark Printer Error Code Ec5 Los Altos Hills, CA Thank you. Lexmark Engine Error The fuser assembly is subject to mechanical wear and heat related degradation and is a scheduled replacement item in most machines at between 200K and 350K pages.

See “Network Wrap Tests” on page 23. http://softacoustik.com/lexmark-printer/lexmark-all-in-one-error.php Ensure your computer is connected and turned on. Carrier Jam There is a cartridge carrier jam. If cables, connectors and connections are good replace assemblies listed. Card format In Photo mode, memory card inserted has incorrect or unsupported format. Lexmark Error Codes Problem

Also, can I get some instructions on putting in the rollers. Shop for Lexmark Maintenance kits * This is a model dependent interval Install maintenance kit and reset maintenance message Purchase Lexmark maintenance kits How did we do? Error 44 Defective font card installed in font slot. http://softacoustik.com/lexmark-printer/lexmark-error-1ec.php Warning A paper other than a plain one was loaded when alignment was initiated.

It may be necessary to remove the re drive assembly to observe the lamp cycling on and off. Lexmark Ms310dn Error Codes For more information, see Installing the print cartridges. Replacement of the thermistor is not a cost effective repair, replace fuser assembly.

For more information, see Memory card reader.

Check connecting cables for continuity. Fuser Pricing How did we do? Check fan for binding or defective bearing - Replace Fan How did we do? Lexmark Crc Failed Do Not Power Off A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again.

Error 30 30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed properly and that it is detected by the ramp on Transfer Roll Error Cannot start servo operation. Remove toner cartridge for better access to jammed paper. http://softacoustik.com/lexmark-printer/lexmark-error-250.php If the tray is difficult to remove, then you may have to remove the tray above or below tray X to remove the jammed pages.

We got it this morning and I have it installed. We can email further info if needed for your particular model. Adjust the settings in the Scan dialog. Disconnect the device.

Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. In Photo mode, image selected is larger than the selected blank paper size. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. Thermistor Check: HOT - J2-1 - J2-2 = 2.5K ohms COLD = 150K ohms to 260K ohms Replace fuser assembly Shop For: Lexmark Maintenance Kits Lexmark Fusers

The heated roller is heated by a halogen lamp or in some cases a solid state ceramic heating element and is subject to failure. The fuser, melts or fuses the toner to the media and has a heat roller and a pressure roller. Observe the lamp through the left near side of the printer. Can be system board or printhead.

May require service technician Press "GO" to clear message and temporarily continue Install Transfer Drum Unit Error 88 Toner Low Toner sensor detects low toner. Check the continuity of the fuser lamp at the two heavy leads. This can significantly improve scanning and overall system performance. Press Select.

Open the printer rear door to access the jam. Error message or title What it indicates Solution Ink low The print cartridge is running out of ink. Most cost effective solution is to replace the fuser Lexmark Fuser Pricing Error 927 Main Fan Stalled, Cartridge Fan or RIP fan stalled, Power off and manually spin fan - it